e Cable length Standard Stroke M L Z 1 m 3 m 5 m Number of stoppable positioning points Output type Nominal size Standard stroke (mm) N P NPN PNP Nil A 3-point stoppable type 5-point stoppable type 16, 25 100, 200, 300, 400, 500, 600, 700, 800, 900, 1000 The remote control type can be selected by adding the above symbols.
, 800 80 Double knuckle joint (with pin) Option 100 25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450, 500, 600, 700, 800 Rod boot Intermediate strokes are available.
Note 3) A particulate generation test has been conducted in a vacuum environment of 10-Pa. a t e l u g c 2 Stainless steel linear guide & low particulate generation vacuum grease e i t n r a e p r a 0.0 10 0 20 10 w t i o o n L Operation cycles a t e l u g c e 1 i t n r a e Particulate generation from the linear guide unit has been reduced with the use of a stainless steel linear guide and
Note 4) For external pilot option, -R, indicate the external pilot specification R for the applicable valves as well. Note 5) The built-in silencer type does not satisfy the IP67 standard.
Because pipe fittings are press-fit, they must be replaced together with the cover assembly. r Those with a bore of 50 or more cannot be disassembled.
MLGC CNA Taper ring Steel ball CB P q f CV/MVG R R CXW CXS CXT MX MXU MXS MXQ Standard manual override lock release MXF MXW Even if air is cut or exhausted, lock release is possible using a wrench. When override is released, lock is engaged again as a fail safe.
L 2*2 *1 Screw lead 10mmReducer ratio "1/3" *2 Screw lead 10mmReducer ratio "1/5" Cable length[m] [m] Cable type* Mounting*1 Motor mountain Nill Without cable Nill Without cable Symbol Type option S Standard cable 2 2 Top/parallel in-line R Robotic cable 5 5 *2 Nill End tapped (Flexible cable) A 10 L Foot(in-line *The motor and encoder cables are included.
Chart (1) 400 st 500 st 600 st 700 st 400 st 500 st 600 st 700 st 10 5 4 300 st 300 st 3 200 st 200 st Load movement time: t (S) 2.
Voltage leaking When a resistor is used along with the switching element and a C-R element is used for protecting the switching element (surge voltage protector), be aware that there is an increase in leaked voltage when the leakage current flows through the resistor or the C-R element. Residual leaked voltage must be kept as follows.
Air dryer model IDF100FS-30-R IDF125FS-30-R IDF150FS-30-R Breaker capacity 20 A 30 A Sensitivity current: 30 mA Corrosion is not covered under warranty. Option symbol V With a timer controlled solenoid valve type auto drain Option symbol Float type heavy duty auto drain is changed to the solenoid valve type auto drain.
L R S Piping port position Nil Operating direction Left Right L R S a b h g d c f e Note) Plugs are installed in ports other than those indicated for the model.
L R S Piping port position Nil Operating direction Left Right L R S a b h g d c f e Note) Plugs are installed in ports other than those indicated for the model.
L R S Piping port position Nil Operating direction Left Right L R S a b h g d c f e Note) Plugs are installed in ports other than those indicated for the model.
GR-S-010(10g) GR-S-020(20g) 6 - R/L side parallel type LEKFS16 18 26 25 Component Parts No. Description Material Note No.
1 u r e q w Material Description No. Body L Body R Main valve Valve guide Nozzle holder Port Elbow Cover Ring Arm Spring Main valve seal Lever 1 2 3 4 5 6 7 8 9 10 11 12 13 PBT PBT PBT o t POM Aluminium alloy Aluminium alloy Anodized Anodized Only for the VMG12m PBT Stainless steel Stainless steel PBT !4 Stainless steel HNBR PBT !5 !0 Only for the VMG11m Combined with the elbow u. !
Through-hole/CQ2YB, CDQ2YB Both ends tapped/CQ2YA, CDQ2YA Both ends tapped (mm) Bore size (mm) 63 O1 R O1 thread R R M10 x 1.5 18 80 M12 x 1.75 22 100 M12 x 1.75 22 H thread effective depth C 4-N through 8-O counter bore U Q F 2-P (Port size) (Rc, NPT, G) I 22 M E D Z 11 Lead wire min. bending radius 10 Auto switch D-A7, A8 K M E S J B + Stroke A + Stroke L Rod end male thread H1 Rod end
Through-hole: CQ2YB/CDQ2YB Both ends tapped style: CQ2YA/CDQ2YA CDQ2YA RE A B Both Ends Tapped (mm) Bore size (mm) O1 R O1 thread REC R R 32 M6 x 1.0 10 40 M6 x 1.0 10 CX 50 M8 x 1.25 14 CY MQQ M RHC H thread effective depth C U 4-N through 8-O counterbore Q F 2-P (Port size) (Rc, NPT, G) MK(2) I RS Q G RS H A 22 D M E Z 11 Lead wire min. bending radius 10 RZQ Auto switch D-A7, A8 MI W S
Through-hole: CQ2YB/CDQ2YB Both ends tapped style: CQ2YA/CDQ2YA CDQ2YA RE A B Both Ends Tapped (mm) Bore size (mm) O1 R O1 thread REC R R 32 M6 x 1.0 10 40 M6 x 1.0 10 CX 50 M8 x 1.25 14 CY MQQ M Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com RHC H thread effective
Mounting: B (Basic Style), Bore Size: 50mm, Port Thread: 20 & 25 Bore: M5 x0.8, 32-50 Bore: Rc Thread, Stroke: 100mm, Option: R (Rear Plate)
Mounting: B (Basic Style), Bore Size: 50mm, Port Thread: 20 & 25 Bore: M5 x0.8, 32-50 Bore: Rc Thread, Stroke: 200mm, Option: R (Rear Plate)