4-channel Flow Monitor (Remote type monitor unit) Refer to the dimension drawing (page 42) for panel cut-out dimensions. Removing the panel mount adapter The product with panel mount adapter can be removed from the installation by removing 2 screws and releasing the hooks at the sides. The hooks can be released by inserting a suitable thin card. Pull the panel mount adapter to the front, and remove the product.
Rc(NPT)11/4 40 to 42 Nm [ oUt2] Output mode (OUT2) [ HYS] Hysteresis mode Element Description Rc(NPT)11/2 48 to 50 Nm [ 2ot] Switch operation (OUT2) [ 2_P] Normal output The switch turns on within a set flow range (from P1L to P1H) during window comparator mode. Set P1L (switch lower limit) and P1H (switch upper limit) using the setting procedure above.
Rc(NPT)11/4 40 to 42 Nm Hysteresis H_1 Item Default setting / With the temperature sensor in parenthesis (Displayed alternately) Flow [L/min] Rc(NPT)11/2 48 to 50 Nm [F 3] Response time setting 1 second Temperature upper limit exceeded If the tightening torque is exceeded, the product can be broken. If the correct tightening torque is not applied, the fittings may become loose.
They are all important notes for safety and must be followed in addition to International standards (ISO/IEC) and other safety regulations. 4 Analogue output (flow rate) Rc(NPT)3/4 28 to 30 Nm Pin number of the connector at the body side Rc(NPT)1 36 to 38 Nm Maintenance Rc(NPT)11/4 40 to 42 Nm Element Description Rc(NPT)11/2 48 to 50 Nm How to reset the product after a power cut or when the
[F80] Setting of power saving mode No setting [display is turned on] Rc(NPT)11/4 40 to 42 Nm Switch ON Switch OFF Do not touch the terminals and connectors while the power is on. Otherwise electric shock, malfunction or damage to the product can result.
[F 2] OUT2 39 No.LFE*-OMY0008 [F3] [F 3] [RES] [F 3] 40 No.LFE*-OMY0008 [F10] OUT1 (OUT2 ) OUT1 (OUT2 ) () OFF [F10] [SUb] OFF OFF OFF OFF [F10] 41 No.LFE*-OMY0008 (20 L/min ) (=P_1 ) (=N_1 ) (=P1L ) (=P1H ) (=N1L ) (=N1H ) 42 No.LFE*-OMY0008 ( ( ( ( ) ) ) ) 9L3 (1.5S)6 (3S) 9L(9) () + 1 (0) 9L 3 (1.5S)6 (3S) 9L 6 0 [0] () + 1 () (=)(=) 1 / 43 No.LFE*-OMY0008 ( ( ( ( ) )
FLT Operation of this product will stop when the alarm occurs. 5.5 Advanced setting mode HRR Series 5-42 HRX-OM-X084 Chapter 5 Display and Setting of Various Functions Communication error alarm detection time 27. Press the [] key. Displays screen for setting the communication error alarm detection time. Time (sec.) to generate alarm AL29: Communication error can be changed.
FLT Operation of this product will stop when the alarm occurs. 5.5 Advanced setting mode HRR Series 5-42 HRX-OM-W002 Chapter 5 Display and Setting of Various Functions Communication error alarm detection time 27. Press the [] key. Displays screen for setting the communication error alarm detection time. Time (sec.) to generate alarm AL29: Communication error can be changed.
FLT Operation of this product will stop when the alarm occurs. 5.5 Advanced setting mode HRR Series 5-42 HRX-OM-X071 Chapter 5 Display and Setting of Various Functions Communication error alarm detection time 27. Press the [] key. Displays screen for setting the communication error alarm detection time. Time (sec.) to generate alarm AL29: Communication error can be changed.
message Response message Code Contents Code Contents 01 Slave Address 01 Slave Address 03 Function 03 Function 0 Head address of specified register 02 Quantity of bytes to read 0001 Quantity of register to read 00EE Information of 0h (circulating fluid discharge temperature: 23.8 oC) FB LRC 0C LRC Request message (Master to Slave) Start Slave Address Function Data LRC End 3A 30 31 30 33 46 42
message Response message Code Contents Code Contents 01 Slave Address 01 Slave Address 03 Function 03 Function 0 Head address of specified register 02 Quantity of bytes to read 0001 Quantity of register to read 00EE Information of 0h (circulating fluid discharge temperature: 23.8 oC) FB LRC 0C LRC Request message (Master to Slave) Start Slave Address Function Data LRC End 3A 30 31 30 33 46 42
60S-2 XLA25-60S-2 2 3 4 XLD-80H5 2 XLA25-60S-2 8 XL-OMY0002 4. 4-1 XLD-25 XLD-40 XLD-50 XLD-63 XLD-80 XLD-100 XLD-160 25 40 50 63 80 100 160 [] 5605150 -6 Pa abs 110 14 45 80 160 200 300 800 L/S 1 0.53 28 2.511 48 418 6.531.5 6.531.5 10 FKM1.310 3/s Pam -11 FKM1.310 KFNW KFNW KDN SUS316L,SUS304,FKM 2 MPa G 0.40.7[ ] 46 200 360 660 1350 3000 5150 3 3 cm O.5MPa 2.5 12 15.5 30 42
temperature, excluding gas permeation Flange type KF(NW) KF(NW),K(DN) Main material Body: aluminum alloy, Bellows: SUS316L, Main part: SUS304 and FKM (standard sealing material) Note 2 Surface treatment for body Outside: hard anodized Inside: basis material Pilot pressure MPa 0.4~0.7 Main pumping 46 200 360 660 1350 3000 5150 Air consumption cm3 for 0.5MPa Note 3 Initial pumping 3.5 12 15.5 30 42
permeation XMD KF(NW) KF (NW),CF KF(NW) KF (NW), K(DN),CF KF(NW), K (DN) Flange type XYD KF(NW) KF(NW) KF(NW) KF(NW), K(DN) KF(NW), K(DN) Main material Body: SCS13(Stainless) Bellows: SUS316L, Main part: SUS304 and FKM (standard sealing material) Note 2) Actuation pressure MPa (G) 0.4 to 0.7 Main pumping 46 200 360 660 1350 Air consumption cm3 for 0.5MPa Note 3) Initial pumping 2.5 12 15.5 30 42
M4x0.7x22L 20 NBA-088S 25 NBA-106S (mm) 32 BGS1-032S 40 BAF-04S 50 BAF-05S 63 BAF-06S 80 BAF-08S 100 BAF-10S D-G5BA mm 20 25 32 40 50 63 80 100 D-G5BA 5 5 5.5 6 7 7.5 7.5 8 30% 1 2 2 mm mm D-G5BA A B Hs 20 25 31.5 31.5 24 26 24 25 28 36 36 46 80 28.5 32 40 50 63 32.5 33 37 36.5 45.5 45.5 42 48.5 57.5 56 100 57 46 68 (mm) 10 20 75 15 3. 3-1. 1 2 3 4 5 6 7 8 9 10 1 2 3 416
10 (MXQ6(B)) (MXQ8(A,B,C),12(A,B,C)) (MXQ8(A,B,C),12(A,B,C)) 11 (MXQ16(A,B),20(A,B),25(A)) (MXQ16(A,B),20(A,B),25(A)) 12 13 A 14 15 16 17 18 19 (MXQ6A,8A,12A, MXQ16(A,B),20(A,B),25(A)) 20 21 22 O 19 / 23 24 25 26 27 28 / 29 30 31 32 33 34 35 36 NBR 37 NBR 38 NBR 39 (MXQ6,8(C),12(C)) / 40 (MXQ6,MXQ8(C),MXQ12(C)) 41 NBR (MXQ6,MXQ8(C),MXQ12(C)) 42
M 10 16. 16-1. 1 22 (mm) gfcm) (mm) 12 RTW-13 5 14 16 RTW-18 6 34 20 RTW-22 8 52 25 RTW-26 10 88 32 RTW-34 14 220 40 RTW-42 14 220 50 RTW-52 17 440 63 RTW-62 17 440 80 RTW-82 22 1,240 100 RTW-102 27 2,000 16-2. 1) 1 1 2) 2 2 11 3) 32 4) 3 3 16-3. 2JIS2 1 , 4 2 3 4 16-4. 1 5 5 6 6 12 () 32 () 32 7 7 () 8 2 1 13 17. 17-1.
Lateral load is applied. 42 - 6. Maintenance 6-1. Construction Fig. 23 Construction No. Description Qty Note No.
Blinking 42 Press WRITE one time. Press LEFT 2 times to shift the blinking cursor. Press UP 3 times to set the value of 3. Press WRITE one time to enter into program STEP Blinking Blinking 4, which is the end of program 1. Press END to end the program setting for program 1. Program 1s programming ends. Set the program no. to 8 through UP to PRG 8.
" " PRG 1 STEP 0 2 WRITE " End End0.0 2 LEFT PRG 1 STEP 1 " " UP 5 " " 5 UP PRG 1 STEP 1 " " 5 " " 1 WRITE 2 PRG 1 STEP 2 " " 3 LEFT " " UP 3 3 ) 41 PRG 1 STEP 2 " " " " 1 WRITE 3 PRG 1 STEP 3 " " 2 LEFT " " UP 3 PRG 1 STEP 3 " " " " 1 WRITE PRG 1 STEP 4 1 1 End " " " " " " 1 PRG 1 STEP 1 " " " PRG 1 STEP 1 UP No.8 " PRG "8" " " PRG 8 STEP 0 2 WRITE " End 42