High Vacuum L Type Valve Do not twist the valve seal 1.
Reset content Item Reset content PS1 0kPa PS2 0kPa *(Note): Gain (GL and sensitivity (SL) are not reset. 24 - Error indicating function Error LED display Contents of error Countermeasure name Please execute "initialize (refer to P33)" when ITV do not operate normally after restarting the power supply. Please contact us, when ITV do not operate normally after initialize.
Do not use lead wire retainers for unclamp angles of 105 , 120 and 135 . Failure example 1 There should be no slack in the lead wire. Lead wire retainers Failure example 2 Do not use the lead wire retainer above the switch. Lead wire Close the cover until you hear a click, and put the excess lead wire in the lead wire storage space.
Do not use any other voltage as this may cause failure. Before mounting the sensor to the cylinder, stop the operation of the device to avoid injury. Do not use the product if there is smoke or a strange smell. Do not handle with wet hands. Avoid getting the product wet. In case of a malfunction, stop using immediately. This product is a piece of precision equipment.
With regards to a breathing port Do not plug a breathing port. Also take care not to prevent intrusion of foreign matters such as dust and water into the breathing port. Mounting Warning About ventilation If air leakage increases or equipment does not operate properly, stop operation.
Wrapping of sealant tape When connecting pipes and fittings, etc. be sure that chips from the pipe thread and sealing materials do not get inside the valve. Furthermore, when pipe tape is used, leave 1.5 to 2 thread ridges exposed at the end of the threads.
Warning Handling (1) Do not use for oxygen. (2) Do not give any modification to the product and its function. (3) Before installation and removal, shut off supply pressure completely and exhaust residual pressure in tubing and other pressure line. -6- Environment Caution (1) Do not mount the product in a location where it is subject to strong vibrations and/or shock. (2) Avoid to expose the
Do not twist the valve seal 1.
When multiple heater assemblies or valves are used, do not apply power to the heater assemblies simultaneously. Keep approximately 30 seconds between applications of power to each heater assembly. This will allow for incremental spacing to prevent harmful large initial surge. 8 XL*-OMI0011-E 4.
Do not use the filter regulator where containing those. Effects organic solvents and chemicals, and where these elements are likely to adhere to the equipment.
Do not operate at pressures or temperatures, etc. beyond the range of specifications, as this can cause damage or malfunction. (Refer to specifications.) Contact SMC when using a fluid other than compressed air (including vacuum).
Do not remove it and attention should be taken not to deform nor gouge. 14 Other Cautions for Operation 7-1) Environment The piston slider has iron part inside. Keep the cylinder tube away from the water. Do not use in atmosphere or place where might corrode the cylinder. Protect the cylinder with cover where it is exposed to dust and particle, drop of water/oil.
Do not operate in locations having an atmosphere of corrosive gases, chemicals, sea water, water or steam, or where there will be contact with the same. 2. Do not operate in locations where vibration or impact occurs. 3. In locations which receive direct sunlight, provide a protective cover, etc. 4. In locations near heat sources, block off any radiated heat. 5.
Do not use valves where there is direct contact with, or in atmospheres of, corrosive gases, chemicals, salt water, water or steam. 2. Do not use in an explosive atmosphere. 3. Do not use in locations subject to vibration or impact. Confirm the specifications for each series. 4. A protective cover should be used to shield valves from direct sunlight. 5.
Do not use the filter regulator where containing those. Effects organic solvents and chemicals, and where these elements are likely to adhere to the equipment.
Do not use the product where these are present.
Do not touch the cylinder during operation at a high speed and a high frequency. Use caution when handling a cylinder, which is running at a high speed and a high frequency, because the surface of a cylinder tube could get so hot enough as to cause you get burned. 2. Do not use the air cylinder as an air-hydro cylinder.
Therefore, do not loosen or remove the hexagon socket head cap screws which secure cover A and cover B. 2. Be sure to contact SMC regarding disassembly or repair, etc. D-X Individual -X 779
Also, do not attach a panel with a thickness beyond the specified range.
Electrical entry T -With conduit terminal TL -With conduit terminal and light D -DIN terminal DL -DIN terminal with light DO-For DIN terminal (without connector, gasket is included.)