Digital Pressure Switch

For the operation in normally open and normally closed, refer to "List of output mode" on page 19. 1. Keep pressing the button for 2 seconds or longer in the measurement mode. After [ ] is indicated, press the button five times. Then, [ ] and current setting appears in turn. 2. Press the or button to select the output type. 3.

Mechanically jointed rodless cylinder Basic type With Slide bearing guide type With cam follower guide type With linear guide type With High rigidity/ Linear guide type With Protective Cover type

Maintenance and Inspection 3.1 Inspection -P. 19 3.2 Maintenance -P. 20 3.3 Replacement Parts -P. 20 4. Troubleshooting -P. 20 -1- Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.

FILTER REGULATOR

HOW TO ORDER" (P8). 19 8REPLACEMENT PROCEDURE WARNING Before replacement, ensure that the regulator is not pressurized. Rotate the pressure adjusting handle to zero. Replace refering to 9DISASSEMBLY DRAWING P24 to P28. After replacement, ensure that specified function is satisfied and external leakage is not found before starting operation.

Magnetically Coupled Rodless Cylinder (Slider Type: Slide Bearing)

Allowable load mass on guides and moment 17/28 18/28 19/28 20/28 21/28 22/28 5.

Regulator Valve

Insufficient tightening of the bolt Foreign matter is caught in the gap betw een the mounting surfaces (19) Abnormal amount of air leakage is found from the 3 (R) port. Foreign matter is caught in the poppet valve on the exhaust side. (3) (6) Foreign matter is caught in the poppet valve on the supply side.

air-filter-e

Symbol Number of arranged elements 4 7 13 19 Number of arranged elements 30 36 55 83 04 07 13 19 30 36 55 83 Symbol Nominal filtration accuracy (m) Note) Nominal filtration accuracy (m) 0.5 1 2 5 10 20 40 Symbol Nominal filtration accuracy (m) 50 70 74 75 100 105 120 X50 001 002 005 010 020 040 050 070 074 075 100 105 120 Symbol Element length Element length L250 L500 (L250 x 2) L750 (L250

AS-FPQ/AS-FPG

ASS ASR ASF Male thread Proper tightening torque Nm Width across flats mm Nominal size of adjustable angle wrench mm M5 1/6 turn after hand tightening 8 100 12 17 19 24 7 to 9 12 to 14 22 to 24 28 to 30 1/8 1/4 3/8 1/2 150 200 200 200 Lock Nut Tightening Torque Caution 1. The proper tightening torque for the hexagon lock nut is as shown in the table.

Speed Controller with Pilot Check Valve with One-touch Fitting Series ASP 1

/16" 1/4" 5/16" 5/16" 3/8" 3/8" 1/2" ASP330F-N01-07S ASP330F-N01-09S ASP430F-N02-07S ASP430F-N02-09S ASP530F-N03-09S ASP530F-N03-11S ASP630F-N04-11S ASP630F-N04-13S 10.5 35.1 39.5 33.9 11.8 1/2" 10-32 UNF NPT 1/8 8 14.2 35 38.9 15.8 10.9 42.6 48.7 15 36.7 NPT 1/8 NPT 1/4 1/2" 18.5 41.7 11/16" 18 68 20.3 23.1 25.9 26.5 107 116 220 230 14.4 50.3 56.2 19.8 41.9 NPT 1/8 NPT 3/8 1/2" 23 46.9 19

MRHQ

Step 2) Refer to Mounting Switches to Verify Opening/Closing of Gripper on page 12-11-19 and position auto switch in switch mounting groove. MRHQ Step 2) Refer to Mounting Switches to Verify Opening/Closing of Gripper on page 12-11-19 and position an auto switch in switch mounting groove. Misc.

MGF

Kit components 40 MGF 40-PS Items 19 through 23 from the table above. 63 MGF 63-PS 100 MGF100-PS 4 Series MGF Dimensions 40 MGF40 Scale: 50% 4-M8 x 1.25 through 100 120 90 9.5 36.5 + Stroke 8 46 + Stroke 7.5 18.5 2-Rc 1/8 port for extending cylinder Breathing hole for guide (with element) When the cylinder is extended 38 Port for retracting cylinder M5: T-slot for hexagon bolt 4-M8 x 1.25

MGZ Series

The start-up time for output in the extending direction will be lengthened by throttling the meter-in speed controller. 19 World Wide Support... North American Branch Offices For a branch office near you call: 1-800-SMC-SMC1 (762-7621) SMC Pneumatics Inc. (Milwaukee) 16850 W. Victor Road New Berlin, WI 53151 Tel: (262) 827-0080 FAX: (262) 827-0092 SMC Pneumatics Inc.

AS-FPQ/AS-FPG

Male thread Proper tightening torque Nm Width across flats mm Nominal size of adjustable angle wrench mm M5 1/6 turn after hand tightening 8 100 12 17 19 24 7 to 9 12 to 14 22 to 24 28 to 30 1/8 1/4 3/8 1/2 150 200 200 200 Lock Nut Tightening Torque Caution 1. The proper tightening torque for the hexagon lock nut is as shown in the table.

NAMUR Interface 3 Port Solenoid Valve Series VFN200N 1

23 Applicable heavy-duty cord O.D.6 to 8 Pg9 24 36.5 66.5 57 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com 32 40 14 Pilot EXH. 2-5.5 Mounting hole 2-1/4 3 1 Manual override (Non-locking) 9 23 VFN212N--02-D 213 19 23 Applicable heavy-duty cord O.D.6 to 8 Pg9 24

VFN2000N

(Flush) Non-locking push type (Extended) Locking type (Tool required) Nil A B Grommet Grommet terminal Conduit terminal DIN terminal G E T D Light/Surge voltage suppressor None Nil DIN terminal (Without connector) DO Z With light/surge voltage suppressor With surge voltage suppressor S Note) Note) Available for grommet type only. 3-12-1 2 Series VFN2000N Dimensions (mm) VFN2120N--02 148 19

Thomas Oil-less Diaphragm Compressor / Vacuum Pump Flow Rate: .65 CFM / 19 LPM , .65 CFM / 19 LPM, Max Pressure: 30 PSIG / 2 bar , 30 PSIG / 2 bar, Max Vacuum: 22 in HgV / -746 mbar , 22 in HgV / -746 mbar, Voltage: (60 Hz) 230 / (50 Hz) 220 , (60 Hz) 230 / (50 Hz) 220, Frequency (Hz): 50 / 60, Phase: 1-phase, Net Weight: 5.1 lbs. / 2.3 Kg Series

FILTER REGULATOR

HOW TO ORDER" (P8). 19 8REPLACEMENT PROCEDURE WARNING Before replacement, ensure that the regulator is not pressurized. Rotate the pressure adjusting handle to zero. Replace refering to 9DISASSEMBLY DRAWING P24 to P28. After replacement, ensure that specified function is satisfied and external leakage is not found before starting operation.

Air Filter

Assembly of Optional Parts 19 8. Operation and Adjustment 20-21 9. Trouble Shooting 22 10. How to Replace the Components 23-28 10-1. Bowl Assembly Replacement 23-25 10-2. Element Replacement 26-28 11. Disassembly Drawing 29 12. Dimensions 30 -1- Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage.

Parallel Style Air Gripper: Wide Type Series MHL2

depth 8 +0.030 0 4 x M10 x 1.5 thread depth 20 6H9 depth 8 +0.030 0 (Mounting thread) Dimensions of auto switch mounting groove (Enlarged view) 40H9 depth 2.5 +0.062 0 Rc (G , NPT ) 1 8 1 8 1 8 Rc (G , NPT ) 1 8 1 8 1 8 Auto switch mounting groove (4 locations) (Finger closing port) (Finger opening port) 2 x M10 x 1.5 (Rack screw) Width across flats 17 (2 locations) Width across flats 19

Series GS40 Digital Pressure Sensor 1

.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com (Lead wire length) 19 3 25 IR 5 9 8 5 VEX 36 1 3 22 22 AMR 3.2 ITV IC M5 type PT type 40 VBA VE SMC DIGITAL PRESSURE SENSOR ALM. SET 20 VY1 + G P.SET PPA AL 14-11-19

IR1000/2000/3000

19 Series IR1000/2000/3000 Flow Characteristics Pressure Characteristics Vacuum pump exhaust speed: 500 l/min VAC side pressure: 101 kPa at initial setting Vacuum pump exhaust speed: 500 l/min IRV1000 IRV1000 0 53.0 10 53.5 20 54.0 SET side pressure (kPa) Set pressure (kPa) 30 54.5 40 55.0 50 Set point 60 55.5 70 56.0 80 56.5 90 100 0 10 20 30 40 50 60 70 57.0 100 95 90 85 80 75 70 65 60