EX600-SPN_eng Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. OFF. Parameter Setting Hardware Configuration I/O Map Diagnostic Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Refer to the valve catalogue for valve manifold dimensions. 1 ASInterface line (+) AS-i + 2 4 (0 V) RESERVE 2 Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Input (Only connector "0") 2 1 2 Input No.1 1 3 Power supply (0 V) 1: Input No.1 is connected to the pin No.2 of the input connector "0", 2 input signals can be directly inputted the input connector "0". 2: N.C.: Not connected 5 3 4 Input 4 Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids.
Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. EX9-PE1 power input connector No.1 M12 5-pin plug B-code Element No.
Do not touch the leakage of fluid without care. If the fluid has high temperature or is chemical, the contact could result in burn and other injuries. 3) Disassembly Do not disassemble the pump. Caution 1) Quality of supplied air Mount the filter with filtration of approx. 0.01.
Do the same for release (push and rotate for 90 degrees). Tighten the piping using the correct torque shown below.
Caution Operating Condition (1) Do not use in atmosphere containing corrosive gas, chemicals or exposed to sea water or vapor. (2) Do not use where vibrate or exposed to impact. (3) When heat source exist nearby, protect the regulator from the radiation heat.
Warning Environment (1) Do not use in environment where the product is exposed to corrosive gas, chemicals, salt water, water or steam. (2) Do not operate the product in a location where it is subject to strong vibration and/or shock. For vibration, it should be within 1G 60Hz. ! ! ! ! -6- 7. Maintenance Warning (1) If handled improperly, compressed air can be dangerous.
Connection 1) Rc connection Confirm that chips from the pipe threads and sealing material do not enter the piping. Also, when sealant tape is used, leave 1.5 to 2 thread ridges exposed at the end of the threads. -4- Piping Piping 2) TSJ connection The TSJ fitting is a kind of a self-align fittings.
Warning Environment (1) Do not use in environment where the product is exposed to corrosive gas, chemicals, salt water, water or steam. (2) Do not operate the product in a location where it is subject to strong vibration and/or shock. For vibration, it should be within 1G 60Hz. ! ! ! ! -6- 7. Maintenance Warning (1) If handled improperly, compressed air can be dangerous.
Do not operate under the conditions listed below due to a risk of malfunction.
(Outlet flow rate:0L/min) Do not rotate the handle to a pressure If the inlet pressure fluctuation is large, the outlet pressure maybe exceeding the max. set pressure. over the setting range of governor, and that will result in an unexpected accident.
Do not exceed the screw-in torque of 3.5 Nm when installing piping. Exceeding this value may cause malfunctioning of the sensor. 4. The minimum bending radius of the cable is 50 mm. 5. Do not use pressure sensors with corrosive and/or inflammable gases or liquids. 1. Incorrect wiring can damage the switch and cause a malfunction or erroneous switch output.
Do not use with pressure or temperature beyond the specification range.
Do not mark or damage lhe piston rod. This could cause damage to packing and resull in lluid 'eakage. O Do not apply oil lo the sliding section of lhe piston rod, O Do nol apply rclary torque. O Do not apply large-load energy to the model wilh a shock absober when ths shock absolbet is absorbrng enrgy twhen the levt is uprighl).
Do not use in locations having an explosive atmosphere. 2. When vibration or impact is applied, make sure to test in the 2.
Do not supply lubrication, as this is a non-lube product. The interior of the cylinder is lubricated at the factory, and lubrication with turbine oil, etc., will not satisfy the product's specifications. 6. Never reapply lubricant. Never reapply lubricant, as there may be a degradation of particulate generation or operation characteristics. 2.
For AC specifications, Nil is only set for electrical entry DO. Right Left Right Left IN IN Options (For details, refer to page 12.)
Use under conditions where pressure fluctuations (pulsations) exceeding 0.1 MPa do not occur. Operating pressure MAX. 0.99MPa Vacuum 1.310-6kPa Operating temperature 5oC to 80oC Element proof differential pressure MAX. 0.1MPa Element reverse differential pressure MAX. 0.05MPa Not possible to use with connecting in reverse.