VBA-OM-S009 Do the drain pulling out regularly.
2 3 L0 V 4 C/Q (IO-Link)/1(SIO) -17No.PS-OMV0003CN-G NPN 2 DC(+) OUT1 OUT2 DC(-) PNP 2 DC(+) OUT1 OUT2 DC(-) IO-Link L+ C/Q IO-Link DO L-18No.PS-OMV0003CN-G [] 3 0.2 [] / UP DOWN OUT1 OUT1 OUT2 OUT2 [F10]30 () SET 1~3 SET 3~5 SET [] [] [] [3 ] (25 ) (55 ) (23 ) (21 ) 30 () 3 -19No.PS-OMV0003CN-G ON OFF ON P_1 H_1 ON OFF ISE70 ISE71 [P_1] OUT1[MPa] 0.500 0.800 [
.(5%) (0~1MPa 0.001MPa 1/1000) () () F () ripple -14No.PS-OMV0008CN-E ( M46L(2)) 0.760.1 Nm A(ZS-50-A) A M4X6L B(ZS-50-B) B M4X6L -15No.PS-OMV0008CN-E 1.50.1 Nm (ZS-48-A) -16No.PS-OMV0008CN-E -02-N02 8~12 Nm -F02 4~5 Nm 24 () -17No.PS-OMV0008CN-E ()336 336 -18No.PS-OMV0008CN-E FG M12 M12 (Port Class A) 1 DC(+) DC1224 V 2 OUT2 2 3 DC(-) 0 V 4 OUT1 1 IO-Link 1 L+ DC1830 V 2 DO
Do not replace the non-rotating guide. Since the non-rotating guide is press fitted, the entire cover assembly needs be replaced instead of a single part. 37
Do not replace the non-rotating guide. Since the non-rotating guide is press fitted, the entire cover assembly needs be replaced instead of a single part. 38
You do not need to specify "N" (i.e., without lead wire) for D-A3A, D-A44A, D-G39A, and D-K39A. This is the only standard specification automatically available for these models.
Note 3) Do not add value to long stroke models. 4 Compact Cylinder Series CQS Accessories Single knuckle joint Double knuckle joint ND hole H10 axis d9 L MM MM NDH10 RR1 RR1 E1 E1 NX NZ A1 U1 L1 A1 U1 NX L1 A A Metric Threads Metric Threads ND H10 NX Pin part No. NDH10 NX Bore size (mm) Bore size (mm) E1 A1 MM U1 Part No. A Part No.
DC () Blue D-F9PW D-Y7PW D-F9P D-Y7P DC (+) Brown DC (+) Brown OUT Black OUT Black DC () Blue DC () Blue Indicator light ON D-F9BW D-Y7BW D-F9B D-Y59B OUT (+) Brown OUT (+) Brown Operating range OFF Red Green Indicator Red Optimum operating position OUT () Blue OUT () Blue Contact Protection Box/CD-P1 1, CD-P12 Internal circuit
Contact Protection Box/CD-P11, CD-P12 The D-Z7, D-Z8 and D-A9 type switches do not have built-in contact protection circuits. Use a contact protection box in cases such as with an induction load, when the lead wire is longer than 5m or with 100VAC. 1 Operating load is an induction load. 2 Wiring to the load is 5m or longer.
low speed actuation (no control of cylinder output) Example 2) Low speed with output control Precision restrictors Solenoid valve ITV (Electro-pneumatic regulator) Mist separator (0.01 m or less) (0.3 m or less) Mist separator (0.3 m or less) Air filter (5 m or less) IR (Precision regulator) W Air filter (5 m or less) IR (Precision regulator) W When performing control of cylinder output, do
Do not subject the gauge to impacts, such as dropping, during transportation and mounting. This can cause loss of indication accuracy. 2. Do not use in locations with high temperature and humidity. This can cause malfunction. 3. When screwing the pressure gauge into place, be sure to apply your wrench on the square wrench flats.
You do not need to specify "N" (i.e., without lead wire) for D-A3, D-A44, D-G39, and D-K39.
When it goes OFF (when an alarm is generated), the controller output should be stopped by the sequence program. 24V, 0.2A or more 24V power supply + 10m or less 5) The LSP and LSN signals do not require wiring, because they are automatically turned ON internally at the time of shipment.
SG 12 Note 1) Do not orient diodes incorrectly. The amp will fail if connected incorrectly. Servo ON Note 2) Wiring for a standard cable less than 10m. When the cable length is 10m or longer, four lines each of P5 and LG wires should be connected in parallel.
Make sure that the lead wires do not interfere with the slide table at any stroke range. Lead wire cover Figure 3.
(Mp,My values do not apply to this example.) Mr=W (L3 + C) = 10 (.05 + 0.014) =0.64 [N m] W Mr 2 =Mr/Mr max. =0.64/12 =0.053 Mr: Mr max. value is from
Perform changes of the detection position under the same conditions as step 3. 24
Series RSDG Auto Switch Hysteresis Contact Protection Boxes/CD-P1 1, CD-P12
Do not dispose this fluid in the environment.
(Do not adjust more than 2mm, as it will not be possible to obtain smooth acceleration and deceleration.) Do not adjust based on the stopper's movement, as this can cause cylinder damage. Stroke Adjustment Loosen the round head Phillips screws, and remove the top covers and dust covers (4pcs.).
Single action positive operation X View M A Automatic / Manual change-over screw (Built-in bleed restriction) Sensitivity adjusting screw (Adjusts GAIN) Stopper screw (Do not move) (15) Diaphragm valve SUP OUT2 OUT1 X (1) Pilot valve Supply valve A Supply valve B (8) Feedback lever (9) Span adjusting lever (7) Exhaust valve Span adjusting lever shaft EXH. (4) Counter weight Diaphragm For