Cylinder with Turntable Series MGT Do not scratch or dent the sliding parts of the piston rod and guide rods. Damage to seals may cause air leaks or faulty operation. 2. In cases where the cylinder will be bottom mounted and shock will be delivered during use, the mounting bolts should be inserted to a depth of 2d or more. 1. Do not put hands or fingers between the plate and body.
(ML2B) (CE1-R) DO-ring Parts sorting: To classify the different types of parts.
Do not apply load and external force on brake and scale plate. Readjustment for brake and scale plates in normal operating condition is not necessary due to preadjustment prior to delivery. Therefore, do not change the setting on adjustment parts carelessly.
Do not perform unlocking while an external force such as a load or spring force is being applied. This is very dangerous because the cylinder will move suddenly.
Do not use this product with special gases, pressure or temperature beyond the specifications. Otherwise, they could cause damage to the product. 4. Post maintenance inspection After installation or repair, perform an appropriate function and leakage test. 5. Modification is prohibited. Do not disassemble or modify the product.
When using on the ejector etc., do not allow liquids such as water or oil to be drawn in with the air. Operating Environment 2. Do not use this product for any purposes that may adversely influence, directly or indirectly, the human body such as for food or medical applications. Warning 1.
Do not use valves in atmospheres of corrosive gases, chemicals, salt water, water or steam, or where there is direct contact with any of these. 2. Do not use in an explosive atmosphere. 3. Do not use in locations subject to vibration or impact. 4. A protective cover, etc., should be used to shield valves from direct sunlight. 5.
A magnet is built inside of guide block for use near a with the auto switch, so do not use near a magnetic disk, magnetic card, or magnetic tape. Data might be erased. 4. When mounting an air slide table, use screws with appropriate length and do not exceed the maximum tightening torque. Tightening with a torque above the limit could malfunction.
DO Bore size (mm) 22 22 30 30 45 45 60 DX DS DH Z DDH10 DC DT DU DR DO DL DE B DA DB Model 20 25 32 40 50 63 80 14 14 20 20 30 30 32 7 7 8 8 10 10 14 44 44 60 60 86 86 110 15 15 18 18 22 22 24 10 10 11.5 11.5 14 14 15 6.6 6.6 9 9 11 11 13.5 9 9 10.5 10.5 12.5 12.5 13 62 62 81 81 111 111 136 42 42 53 53 73 73 90 32 32 43 43 64 64 78 39 43 49 59 71 82 106 +0.058 0 +0.058 0 129 151 185 208
Do not use valves in such environments where corrosive gases, chemicals, or brine or water or steam is airborne, or where valves can be directly exposed to any of those. 2. Do not use in locations influenced by vibrations or impacts. 3. This vacuum regulator always uses atmospheric air, therefore, do not use in dusty environments. 4.
Do not use pressure sensors with corrosive and/or flammable gases or liquids. 4. Connection of sensor connector Cut the sensor cable as illustrated to the right. Referring to the table below, insert each lead wire of the cable at the position marked with a number corresponding to 1.
Do not use in an area where a magnetic field is generated. Trimmer auto switches will malfunction or magnets inside actuators will become demagnetized. 2. Do not use in an environment where the trimmer auto switch will be continually exposed to water.
Do not apply external force to the coil when holding it to connect piping, as the tube may deform. When attaching fittings to a solenoid valve, do not use fittings that do not conform to the quick fastener standard. Handle with care when attaching fittings because the application of excessive stress to the quick fastener portion could damage the body. 1.
Do not scratch the sliding portion of the piston rod or the outside threads of the outer tube. Do not scratch or gouge the sliding portion of the piston rod or the outside threads of the outer tube by striking it with an object, squeezing it, or by forcefully wedging a set screw in it.
Cylinders may be damaged if shock absorbers that do not have the recommended characteristics are used.
(Please do not change) < [B] Area1, Area2> The condition at which the AREA output signal is turned on. The AREA output is a signal to be output when the position enters the specified range. The AREA 1 and AREA 2 in the setting items define this output range.
Do not use the product where these are present.
If the product is operated at a pressure lower than the minimum operating pressure, it may cause deterioration in the performance or malfunction. 4 - Installation Warning 1) Do not drop or apply impact during transportation or installation. It will cause damage to the product and result in operation failure. 2) Do not install in areas of high humidity or high temperature.
Do not use the product where these are present.