CJ2X/CUX/CQSX/CQ2X/CM2X Elbow/Universal Type Air Flow/Effective Area Model AS121FM-M5 AS131FM-M5 AS221FM-01 AS231FM-01 AS221FM-02 AS231FM-02 RE A B 3.2, 4, 6 3.2, 4 6, 8 4 6 8, 10 Metric size Tubing O.D.
Elbow/Universal Type Air Flow/Effective Area Model AS121FM-M5 AS131FM-M5 AS221FM-01 AS231FM-01 AS221FM-02 AS231FM-02 RE A B 3.2, 4, 6 3.2, 4 6, 8 4 6 8, 10 Metric size Tubing O.D.
URL http://www.smcworld.com Akihabara UDX 15F, 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021, JAPAN Phone: +81 3-5207-8249 Fax: +81 3-5298-5362 Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer.
URL http://www.smcworld.com Akihabara UDX 15F, 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021, JAPAN Phone: +81 3-5207-8249 Fax: +81 3-5298-5362 Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer. 2011-2016 SMC Corporation All Rights Reserved EX-OMO0031-B
Akihabara UDX 15F, 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021, JAPAN Phone: +81 3-5207-8249 Fax: +81 3-5298-5362 Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer. 2015-2017 SMC Corporation All Rights Reserved. EX-OMT0014-A
If the installation is using accurate control, wait until the product has warmed up (approximately 10 to 15 minutes). 1.0 to 1.2 Yellow ZS-28-C-1 Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result.
During the zero clear operation, pressure above 10%F.S. has been applied. After 3 s, the mode will reset to the measurement mode. The zero clear range can vary 1 digit with individual product differences. Perform zero clear operation again after restoring the applied pressure to an atmospheric pressure condition.
L/min. or CFM(ft3/min.) x 10-2 are the selectable display units. To use for flow rate indication, select the sensor and units before setting the functions [F1], [F2], [F4]. The set values for [F1], [F2] and [F4] will be reset when the flow indication setting is changed.
Akihabara UDX 15F, 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021, JAPAN Phone: +81 3-5207-8249 Fax: +81 3-5298-5362 Regulator Recessed part To change setting, refer to the operation manual from SMC website (URL https://www.smcworld.com) or contact SMC.
If the installation is using accurate control, wait until the product has warmed up (approximately 10 to 15 minutes).
Butyl acetate concentration 10% or less Nitric acid Pure water Caution Sodium hydroxide x Super pure water Strip the lead wire as shown. Do not cut the insulator. Do not touch the terminals and connectors while the power is on. Otherwise electric shock, malfunction or damage to the product can result.
Temperature lower limit under The fluid temperature is below -10 oC. Rise the fluid temperature. [ dtH2] Delay time setting at ON [ 0.00] 0.00 s The function number is increased and decreased by the UP and DOWN buttons.
They are all important notes for safety and must be followed in addition to International standards (ISO/IEC) and other safety regulations. 04 Equivalent to M3 (L=6) 20 0.04 to 0.05 Nm 40 Equivalent to M4 (L=10) 0.09 to 0.10 Nm Element Description This unit supplies the fluid from the supply side main piping to the application.
[F20] Setting of external input Accumulated flow external reset Free range analogue output for instantaneous flow: OFF * (Analogue output for fluid temperature) Temperature lower limit exceeded The fluid temperature is below -10 oC. Rise the fluid temperature. Avoid any sealing tape getting inside the piping. Ensure there is no leakage from loose piping.
URL http://www.smcworld.com Akihabara UDX 15F, 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021, JAPAN Phone: +81 3-5207-8249 Fax: +81 3-5298-5362 Refer to the outline dimension drawing for mounting hole size. Refer to the product catalogue or SMC website (URL http://www.smcworld.com) for more detailed information.
Card URL http://www.smcworld.com Akihabara UDX 15F, 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021, JAPAN Phone: +81 3-5207-8249 Fax: +81 3-5298-5362 Rev.A Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer. 2010-2011 SMC Corporation All Rights Reserved
ON delay time ON point delay time of the switch output can be set. 0.00 second Measurement mode Temperature lower limit exceeded The fluid temperature is below -10 oC. Rise the fluid temperature. OFF delay time OFF point delay time of the switch output can be set. 0.00 second Installation Use the product within the specified operating pressure range and temperature range.
During the zero adjustment, potential exceeding the default setting value by 10%F.S. has been applied. : After approx. 1s measurement mode will return automatically. Slight displacement occurs depending on individual product differences and the sensor adjustment condition at zero adjustment.
Power consumption 10 W specification: Please consult with SMC. When operating with an energy saving driver, continuous energization with the holding voltage of 8 to 16 VDC is possible. Wiring 1. Use electrical circuits which do not generate chattering in their contacts. 4. Power consumption 4W specification: Possible Energizing Time and Non-Energizing Time 2.
No.LV20***-OMY0005 / / / / / / / / LVA/LVC 1 P2 2 P34 3LVC P56 4LVC () P7 5LVA P89 6LVA () P10 7 P11 8 P12 9 P13 1 2 3 4 5 6 7 8 9 10 11 12 13 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN Tel: + 81 3 5207 8249 Fax: +81 3 5298 5362 URL https://www.smcworld.com Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer. 2020