06-cbg1-e Do not replace the bushings. The bushings are press-fit. To replace them, they must be replaced together with the cover assembly. 2. To replace a seal, apply grease to the new seal before installing it. If the cylinder is put into operation without applying grease to the seal, it could cause the seal to wear significantly, leading to premature air leakage. 3.
Do not replace the non-rotating guide. Since the non-rotating guide is press fitted, the entire cover assembly needs be replaced instead of a single part. 200
Do not replace the non-rotating guide. Since the non-rotating guide is press fitted, the entire cover assembly needs be replaced instead of a single part. 202
Do not disassemble the trunnion style. Seal kit includes a grease pack (40, 50: 10 g, 63, 80: 20 g, 100: 30 g). Order with the following part number when only the grease pack is needed. Grease pack part no.: GR-S-010 (10 g), GR-S-020 (20 g) 35
CA2H100A-PS Do not disassemble the trunnion style. Seal kit includes !4, !5 and !6. Order the seal kit based on each bore size. Seal kit includes a grease pack (40, 50: 10 g, 63: 20 g). Order with the following part number when only the grease pack is needed. Grease pack part no.: GR-S-010 (10 g), GR-S-020 (20 g) 40
Piston seal NBR Cushion valve seal NBR O-ring MBW100-PS Cylinder tube gasket NBR Do not disassemble the trunnion style. Seal kit includes !2, !3, !4 and !6. Order the seal kit based on each bore size. Seal kit includes a grease pack (40, 50: 10 g, 63, 80: 20 g, 100: 30 g). Order with the following part number when only the grease pack is needed.
CA2WH100A-PS Do not disassemble the trunnion style. Seal kit includes !0, !1 and !2. Order the seal kit based on each bore size. Seal kit includes a grease pack (40, 50: 10 g, 63 or more: 20 g). Order with the following part number when only the grease pack is needed. Grease pack part no.: GR-S-010 (10 g), GR-S-020 (20 g) 41
Do not replace the bushings. The bushings are press-fit. To replace them, they must be replaced together with the cover assembly. 2. To replace a seal, apply grease to the new seal before installing it. If the cylinder is put into operation without applying grease to the seal, it could cause the seal to wear significantly, leading to premature air leakage. 3.
Do not replace the bushings. The bushings are press-fit. To replace them, they must be replaced together with the cover assembly. 2. To replace a seal, apply grease to the new seal before installing it. If the cylinder is put into operation without applying grease to the seal, it could cause the seal to wear significantly, leading to premature air leakage. 3.
(Rubber, Metal sliding parts: Fluorine coated) Non-greased specification H/DL L/LL Single plug With check valve Single socket Metal part: Stainless steel 304, Rubber material: Fluororubber (Special FKM) Material KC With male thread sealant Seal Note 1) Do not use the S couplers with a leak tester or for vacuum retention because they are not guaranteed for zero leakage.
Note 4) When using the D-M9lA(V) or Y7BA, do not use the steel set screws which are included with the above auto switch mounting brackets (BA7-lll, BA4lll). Order a stainless steel screw kit (BBA1) separately, and use the M4 x 6 L stainless steel set screws included in the BBA1. Note 5) There is a difference in the cylinder tube thickness depending on the cylinder model.
Additionally, do not put the tube end in the liquid. This may cause the back pressure to be applied, resulting in poor performance. 3.Liquids cannot be collected by the air. 1076 A
When the line is stopped, do not adjust or set the differenital pressure, as it could cause the differential adjustment valve to break. 3. When setting the pressure differential, if there is a fluctuation in the operating flow rate, set the pressure differential at the lower flow rate range.
Do not use a tool when rotating the handle. When the handle is rotated with a tool, it may apply excessive torque to the handle or inside the valve body and it may cause damage. Rotate the handle by hand. 9. When locking the valve with LOTO feature in the closed position, use safety lockout hasp.
Do not use a tool when rotating the handle. When the handle is rotated with a tool, it may apply excessive torque to the handle or inside the valve body and it may cause damage. Rotate the handle by hand. 9. When locking the valve with LOTO feature in the closed position, use safety lockout hasp.
Do not use the regulator with flow exceeding the Max. flow indicated in Flow Rate Characteristics as this can cause failure in pressure adjustment. Bleed port Component Parts Knob locking screw No.
/Single Unit), Solenoid Valve Option: G (SUS Body, NBR Seal, Class B), Suffix: Standard, Port Size: 01 (1/8), Thread Type: N (NPT), Voltage: 5 (24VDC), Lead Wire: DO (DIN Connector without Connector), Bracket: B (Bracket)
110.0 to 110.0 kPa2 MPaPressure sensor: Stainless steel 630, Fitting: Stainless steel 304Fluids do not corrode stainless steel 630 and 304R1/4, NPT1/4, G1/4?, URJ1/4, TSJ1/4, Rc1/8Piping direction: Rear/Bottom12 to 24 VDC ?
110.0 to 110.0 kPa2 MPaPressure sensor: Stainless steel 630, Fitting: Stainless steel 304Fluids do not corrode stainless steel 630 and 304R1/4, NPT1/4, G1/4?, URJ1/4, TSJ1/4, Rc1/8Piping direction: Rear/Bottom12 to 24 VDC ?
110.0 to 110.0 kPa2 MPaPressure sensor: Stainless steel 630, Fitting: Stainless steel 304Fluids do not corrode stainless steel 630 and 304R1/4, NPT1/4, G1/4?, URJ1/4, TSJ1/4, Rc1/8Piping direction: Rear/Bottom12 to 24 VDC ?