ISE70/75/75H Do not attempt to rotate the connector, as it is not rotatable.
Please make sure that operating conditions do not cause problems since the use of FEP tubing under chemical environment is unsecured.
In incorporating the element to the element guide, do not drop the element from the upper end of the element guide. Actuators Modular F.R.L.
Types of air Do not use compressed air containing chemicals, synthetic oil which includes organic solvents, salt, corrosive gases, etc., as this can cause damage or malfunction. Operating Environment Mounting Warning Caution 1. Do not use ordinary fittings in locations where static electric charge will cause a problem. This can cause defects or failure of the system, etc.
In incorporating the element to the element guide, do not drop the element from the upper end of the element guide. Actuators Modular F.R.L.
Do not use in locations having an explosive atmosphere. 2. Do not operate in locations where vibration or impact occurs. 3. In locations near heat sources, block off radiation heat. 4. Do not use in environments which exceed the ambient temperature specifications of the product. Caution 1.
Operating pressure Do not use the product beyond the operating pressure range. Do not use in locations where peak pressure exceeds the operating pressure due to water hammer, surge pressure, etc. FGC Bag filter FGF FGF Fluid release valve Tank FGH 2. Operating temperature Do not use the product beyond the operating temperature range.
Do not lift the product by holding the panel, fittings or piping. Never lay the product down for transportation. This may lead to damage to the product. Do not modify the standard product using any of the optional specifications once the product has been supplied to a customer. Check the specifications carefully before selecting an air dryer.
Do not use in an atmosphere where corrosive gas es, chemicals, sea water, water, or water steam is present. Do not use in cases where there is direct contact with any of the above. 2. Maintenance space Allow sufficient space for maintenance and inspection. 2. Do not use in a place subject to heavy vibration and/or impact. 3. Observe the tightening torque for screws.
Connection Be sure that chips from the pipe threads and sealing material do not get inside the piping. Further, when sealant tape is used, leave 1.5 to 2 thread ridges exposed at the end of male threads. Do not use with gases. 4.
Do not exceed the screw-in torque of 13.6 Nm when connecting the pipe to the switch. Exceeding these values may cause the switch to malfunction. 4. Do not use pressure sensors with corrosive and/or flammable gases or liquids. 3. Some fluids may generate static electricity when resin piping is used for piping.
Connection Be sure that chips from the pipe threads and sealing material do not get inside the piping. Further, when sealant tape is used, leave 1.5 to 2 thread ridges exposed at the end of male threads. Do not use with gases. 4.
Do not attempt to rotate the connector, as it is not rotatable.
Do not use this product with special gases, pressure or temperature beyond the specifications. Otherwise, they could cause damage to the product. 4. Post maintenance inspection After installation or repair, perform an appropriate function and leakage test. 5. Modification is prohibited. Do not disassemble or modify the product.
Do not use in an area where a magnetic field is generated. Trimmer auto switches will malfunction or magnets inside actuators will become demagnetized. 2. Do not use in an environment where the trimmer auto switch will be continually exposed to water.
Do not use in a location having an explosive atmosphere. 2. Do not operate in locations where vibration or impact occurs. 3. Do not use in locations where radiated heat will be received from nearby heat sources. 1. Operate within the ranges of the maximum operating pressure and back pressure. Caution 1.
Do not operate with the magnetic coupling out of position. If the magnetic coupling is out of position, push the external slider (or the piston slider by using air pressure) back to the proper position at the stroke end. (When pushing the external slider, do not push it with bare hands.) 4. Do not apply lubricant, as this is a non-lube product.
Do not operate with the magnetic coupling out of position. If the magnetic coupling is out of position, push the external slider (or the piston slider by using air pressure) back to the proper position at the stroke end. (When pushing the external slider, do not push it with bare hands.) 4. Do not apply lubricant, as this is a non-lube product.
Do not touch the leakage of fluid without care. If the fluid has high temperature or is chemical, the contact could result in burn and other injuries. 3) Disassembly Do not disassemble the pump. Caution 1) Quality of supplied air Mount the filter with filtration of approx. 0.01.
ZSM PFl Piping IFl Caution qPiping materials Do not mount any equipment or fittings between the switch body and the detection nozzle in order to avoid leaks and pressure drops. Do not use one-touch fittings in applications where these fittings might be exposed to liquid being sprayed onto them.