ISE70_71-AB.eng An injury or failure can result. 3 Step Setting Mode Maintenance Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
SET for 2 s or longer Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. 1. 1) OUT1 operation mode setting SET 1. 2) OUT1 output mode setting Troubleshooting Do not operate in an atmosphere containing flammable or explosive gases.
The output OUT1(1) set value input mode is selected. 1: The set value of P1 is -50 Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
Do not use pressure sensors with corrosive and/or flammable gases. 7. The applicable fluids are air, non-corrosive gas and non-flammable gas. Consult with SMC if the switch is to be used with other types of fluids. Caution Connection Caution 1. Do not drop, bump, or apply excessive impacts (100 m/s2) while handling.
Connection Be sure that chips from the pipe threads and sealing material do not get inside the piping. Further, when sealant tape is used, leave 1.5 to 2 thread ridges exposed at the end of male threads. Do not use with gases. 4.
Do not attempt to rotate the connector, as it is not rotatable.
Do not hit the table with the workpiece in the positioning operation and positioning range. 11. When mounting the product, use screws with adequate length and tighten them with adequate torque.
Do not use in an atmosphere having corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. 2. Do not operate in locations where vibration or impact occurs. 3. In locations which receive direct sunlight, provide a protective cover, etc. 4. In locations near heat sources, block off any radiated heat. 5.
Do not operate by fixing the table and moving the actuator body. 16. The belt drive actuator cannot be used vertically for applications. 114
Do not use compressed air that contains chemicals, organic solvents, salt, or corrosive gases. Failure to discharge the condensate will allow the accumulated condensate to flow over to the outlet side. Do not use compressed gas containing chemicals, organic solvents, salt, or corrosive gas. This can cause rust, damage to rubber and resin parts, or malfunction. 4.
Do not exceed specified current or the LED might be damaged and not function. 3. The indicator light is lit when switch is off for D-P70 4. Do not drop, dent, or allow excessive impact to cylinder during handling. 5. Keep at least 20mm away from each other when 2 or more cylinders with high magnetic field resistance auto switch are mounted in parallel. and D-P75.
Do not separate the cylinder from the valve. 2. Do not disassemble or modify the guide rod. 3. This product should not be used as a stopper. Cushion Rubber bumper Stroke length tolerance dose not include the amount of bumper change.
Do not apply negative pressure. It may result in malfunction. Should they remain, they could cause malfunction. 3. When connecting pipes and fittings, etc., be sure 3. Do not supply air pressure from ports other than that neither chips from the pipe threads nor sealing material get inside the valve.
Do not service or attempt to remove product and machinery/ equipment until safety is confirmed. 1. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.
Do not use standard dew point 40C (symbol L) type, standard dew point 60C (symbol S) type and IDG30, 50, 30H, 50H for dehumidifying breathing air. Do not use only outlet air (dried air) in a closed room. Caution 1. Devise a layout which considers the position of purge air discharge ports. Purge air is humid air.
Do not operate the cylinder in such a way that an external force causes the workpiece to move while being clamped (Fig. (6)). 6. Furthermore, do not operate the cylinder in an application in which a rotational force will be applied to the piston rod. RE A B REC CX 1. Do not operate the cylinder horizontally. CY 2. Do not perform any work in the rotary direction.
In the case of auto switch rail mounting style, do not remove the rail that is mounted.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not use the product in a place where static electricity is a problem. Otherwise it can cause failure or malfunction of the system.
Function selection mode Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. Reset applied pressure to a level within the set pressure range.