This product is obsolete. Please contact us for the latest version.sales@ocaire.com, MANIFOLD, VALVE, VV2Q* MANIFOLD VQ 2-PORT, 2J, VV2Q* NO SIZE RATING, 1.55897 lb
The VQ20/30 series is a pilot operated, two port multi-media valve. The series is compact and lightweight with a large flow capacity. The VQ20/30's long life, high speed coil (up to 20 million cycles at 100cps for pneumatic use) along with its all plastic construction, make it an excellent choice for those who want high performance at a lower cost.Manifold for VQ20/30 pilot operated valve
The VQ20/30 series is a pilot operated, two port multi-media valve. The series is compact and lightweight with a large flow capacity. The VQ20/30's long life, high speed coil (up to 20 million cycles at 100cps for pneumatic use) along with its all plastic construction, make it an excellent choice for those who want high performance at a lower cost.Manifold for VQ20/30 pilot operated valve
This is a legacy product. Please contact us for the latest version.sales@ocaire.com, MANIFOLD, VALVE, VV2Q* MANIFOLD VQ 2-PORT, 2J, VV2Q* NO SIZE RATING, 1.24869 lb
I/O Configurator (NFC version) Do not connect multiple NFC readers / writers to a PC. Connection details of the I/O Configurator for NFC and the wireless unit Before the wireless system can be used, it is necessary to pair each Remote with its Base using the I/O configurator for NFC. The following sections of this document should be read before using the I/O configurator for NFC; 2.
Do not connect multiple NFC readers / writers to a PC. Connection details of the I/O Configurator for NFC and the wireless unit Before the wireless system can be used, it is necessary to pair each slave with its master using the I/O configurator for NFC. The following sections of this document should be read before using the I/O configurator for NFC; 2.
DO (n+1) Output interface Short circuit protection 0 V DO (n) FE / Shield Output circuit / Bus interface 24 V (logic / sensors) 0 V (logic / sensors) 24 V (valves / loads) 0 V (valves / loads) FE BUS . 8-3 EX245-DY1 60 No.EX-OMU0020CN 9.
Do not connect multiple NFC readers / writers to a PC. Connection details of the I/O Configurator for NFC and the wireless unit Before the wireless system can be used, it is necessary to pair each slave with its master using the I/O configurator for NFC. The following sections of this document should be read before using the I/O configurator for NFC; 2.
Note Please do not use it for purposes other than the original purpose. This connector may only be operated when under no load. Working with wet hands causes electric shock. Please never perform a repair.
(Do not use a tool.) For setting the initial pumped amount, turn it counterclockwise. 2. Opening the valve (valve S) for initial pumping When air pressure is applied to the pilot port 1(P) and the initial pumping solenoid valve is energized, the S valve will release from the S valve seal assembly and open to the adjusted angle. 3.
(The test was performed with the electric actuator in the initial state.) 8) Do not use the product in an environment where it is exposed to oils such as cutting oil, and water. Please install an appropriate protective countermeasure.
When the element comes to the end of its life immediately replace it with a new filter or replacement element (cartridge type). 4 Do not disconnect and replace the one-touch fitting. Environment Warning Warning 1. Do not use the product in the following environments, which could cause failure. Seals the element, cover and fitting body. A place exposed to water, steam or oil.
Do not use solvents such as benzene, thinner etc. to clean the product including the switch cover. Use a soft cloth to remove stains. Refer to the SMC website (URL http://www.smcworld.com) for more information about troubleshooting. This operation manual refers to all standard types and is partially applicable to special models.
Do not use solvents such as benzene, thinner etc. to clean the product including the switch cover. Use a soft cloth to remove stains. Refer to the SMC website (URL http://www.smcworld.com) for more information about troubleshooting. This operation manual refers to all standard types and is partially applicable to special models.
Do not use solvents such as benzene, thinner etc. to clean the product including the switch cover. Use a soft cloth to remove stains. Refer to the SMC website (URL http://www.smcworld.com) for more information about troubleshooting. This operation manual refers to all standard types and is partially applicable to special models.
for mounting attachment) 46 58 45 45 42 26H9 + 0.052 depth1.5 0 30 Positioning pin hole 60 18 5 86 30 107 Auto Switch Mounting Groove Dimensions M5 x 0.8 (Finger opening port) 14 24 M5 x 0.8 (Finger closing port) 42 8 3 4 3 MHY2-25D2 Opening/Closing direction through-hole type 4 x 5.5 through (Hole for mounting attachment) 12 -0.005 -0.025 6 12 22.5 (Limted area for mounting attachment) Do
Do not use the cylinder in the locked state to sustain a load that involves impact. Stopping Accuracy (Not including tolerance of control system.)
When air is supplied to all ports after the solenoid valve is pressure-center positioned, the pistons for rotary operation do not have any thrust, as the pressure in both sides is equal, and the pistons for rotary operation move to the center position due to the thrust of the pistons for center stop.
Do not place your fingers in the clearance between the non-rotating plate and the cylinder tube. Your fingers could get caught between the table and the cylinder tube when the piston rod retracts. If fingers are caught in a cylinder, there is a danger of injury due to the strong cylinder output, and therefore, caution must be exercised. 2.
Note) Do not apply rotational torque to the piston rod. q MK/MK2 RSQ/RSG Connect the shield wire to FG (frame ground).