3 Port Solenoid Valve, VQ100 Series, Base Mounted Type How to Order Valve 10 VQ110 External non-leak specifications 9 Series VQ100 Base Mounted Plug-in Unit The broken line indicates DIN rail mounted type (-D) and side entry connector (S).
Do not use this product in an area that is dusty, or in an environment in which water or oil splashes on the cylinder. ! Caution 1. Martensitic stainless steel is used for the finger guide , so make sure that anti-corrosiveness is inferior to the austenitic stainless steel.
(control operation) LC3F2 Command an operation in the reverse direction only after a cylinder rod stopped completely. LC3F2 Do not operate a cylinder rod with an external force when the electric cylinder directional control driver is turned off or output is in the off state.
S 1 p c . n n p c s . L Long leads uountng B Front Nose Mount C -Rear Pivot E -Double End K -Non-Rotating Rod R -Block Mount W-Double Rod Auto.Switch 853. D-853 Gsg D-G59 B54. D-854 K59 D-K59 864 .
Endurance Test An ozonizer was used in a pneumatic circuit to prepare air to an ozone concentration of 1ppm. The test specimens (system components made from HNBR and NBR) were operated using this ozoneladen compressed air, and the endurance of each type of component/material was measured and compared.
Series AS-FG Speed Controller with One-touch Fittin Stainless Series. 5 5 6 7 9 11 11 11 11 12 13 13 13 15 15 16 16 16 17 17 18 19 21 22 22 23 24 25 27 27 27 29 30 31 31 31 32 34 35 35 35 36 36 37 37 37 38 38 39 39 39 41 42 43 43 43 44 45 46 46 Specifications. How to Order . Construction. Dimensions . Series AS-FG Speed Controller with One-touch Fittings Stainless Series In-line Type.
High efficiency nozzle/KNH (mm) Model Nozzle size D Connection thread L1 A Width across flats H1 Connection thread Weight (g) KNH-R02-100 KNH-R02-150 KNH-R02-200 1 1.5 2 R 1/4 R 1/4 R 1/4 14 14 14 52 52 52 46 46 46 38 38 38 D H1 A L1 Reference dimensions after R thread installation. The air blow thrust is improved by 10%.
31.5 4 45 40 (45) 22.5 VZA (50) VTA 39.6 23.5 (60) (31.5) 1/4, 3/8 1(P), 3(R) port VGA (Distance between ports) VPA VPA 1P 3R 32 3 NO 7 VPA3 M5 x 0.8 (Breathing hole) 25.6 30.7 76.8 For vacuum/VPA542V-1(-F) 02 03 A B 1/4, 3/8 2(A) port 41.1 2 x 4.2 (For mounting) 26 NC 2A 3.5 (1.6) 31 25.6 91 (9) 2 x 4.2 (For mounting) 1/8 12(PA) port (Mounting groove for M5 thread) (5.4) 12 (45) 46 31.5
The part numbers are as follows: G36(46)-2-01, G36(46)-4-01, G36(46)-7-01
May S AS BS CS DS ES FS . Caution If instructions are not followed there is a possibility of injury or equipment damage. Jun T AT BT CT DT ET FT . When dispose the product, contact an industrial waste disposal company for disposal of the product. To minimize the risk, drain the fluid from the product when it is scrapped.
DENMARK SMC Pneumatik A/S FINLAND SMC Pneumatics Finland OY FRANCE SMC Pneumatique SA GERMANY SMC Pneumatik GmbH HUNGARY SMC Hungary Ipari Automatizlsi Kft. IRELAND SMC Pneumatics (Ireland) Ltd. ITALY SMC Italia S.p.A. LATVIA SMC Pneumatics Latvia SIA NETHERLANDS SMC Pnuematics BV. NORWAY SMC Pneumatics Norway A/S POLAND SMC Industrial Automation Polska Sp.z.o.o.
Also, during an emergency stop or a power outage, no current will be applied to the valve, and the pressure in the cylinder will be sealed. Manual valve (Built-in base) When an emergency stop is input or a power outage lasting longer than 5 minutes occurs, the set data will be erased.
After 3 s, the mode will reset to the measurement mode. The zero clear range can vary 4 digits with individual product differences. 3.2 or more 3.2 or more Perform zero clear operation again after restoring the applied pressure to an atmospheric pressure condition.
Install an air filter at the upstream side close to the impact blow valve. Select an air filter with a filtration degree of 5m or finer. 2. Take appropriate measures to ensure air quality, such as by providing an aftercooler, air dryer, or water separator.
Tightening without holding female thread applies an excessive force to the piping bracket directly, leading to breakage.
The assembly, operation and maintenance of machines or equipment including our products must be performed by an operator who is appropriately trained and experienced. 3.
Nil S n TN TF 50, 63, 80, 100 Applicable auto switches vary depending on the bore size. Select an applicable one referring to the table below. Cylinder stroke (mm) Refer to Standard Stroke on page 957.
Note 2) V, S and R specifications are 45T or 45T1 only.
Install an air drier or aftercooler before the regulator. Caution 1. Install an air filter at the upstream side of this product. Select an air filter with a filtration degree of 5m or finer. 2. If an excessive amount of carbon powder is present, install a mist separator on the upstream side.