VBA-OM-S002 Do the drain pulling out regularly.
Free mount Speed controllers do not protrude from the top of the body. Top mount Bottom mount Side mount Wiring and piping direction can be selected depending on mounting conditions.
They do not guarantee an actual fixed range (expect approximately 30% dispersion).
There may be large variations depending on the surrounding environment (variations as much as 30%). 12 Compact Cylinder Series CQ2 Auto Switch Mounting Contact Protection Boxes/CD-P11, CD-P12 Auto Switches/Proper Mounting Position for Stroke End Detection D-Z7 and D-Z8 type switches do not have internal contact protection circuits.
(between lead wire and case) Withstand voltage Ambient temperature 10 to 60C Enclosure IEC529 standard IP67, JISC0920 watertight construction Contact Protection Boxes/CD-P11, CD-P12 Lead Wire Length
I installed \tl .1 onry) f e lri=d.c-) L Type of actuation With irdicator ght and surge v0rrage suppress0r 1 INormal closed 2 lNormal open S and Z not available lor grornmel. i 1 oVAC type inc udes S (do not specity). Body Port size ut subplate _,,' (a --1ry1 wv : Standard typerindividual gilot exhaust l--l l ?
Do not apply a load that involves shocks such as those caused by pounding (particularly with the ball bushing style). 4. If this mass is applied, the deflection of the guide shaft will also have a large value.
Do not hold the terminal block box or the switch. ISE70 ZSE80 ISE80 Lead wire with connector ZSE ISE Knurl ZSP PS 3. Connect the colored wires coming from the cable terminal. Refer to the circuit diagram and table above to avoid mistakes.
Do not scratch or gouge the sliding portion of the piston rod. Damaged seals etc. will result in leakage or malfunction. 4. Do not dent or scratch the mounting surface of the body and the plate. The flatness of the mounting surface may not be maintained, which would cause an increase in sliding resistance. 5.
Do not service or attempt to remove product and machinery/ equipment until safety is confirmed. 1. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.
system Natural air cooling Operating temperature range 0C to 40C (No freezing) Operating humidity range 90% RH or less (No condensation) Storage temperature range 10C to 60C (No freezing) Storage humidity range 90% RH or less (No condensation) Insulation resistance Between all external terminals and the case: 50 MW (500 VDC) Weight 1050 g (Screw mounting), 1100 g (DIN rail mounting) *1 Do
" 0.006 8.3 Note 2) Rotating torque under pressure 0.5 MPa Note 3) Do not use the fittings with a leak tester or for vacuum retention because they are not guaranteed for zero leakage.
As the connected actuator will start operating due to this manual operation, be sure to confirm that it is safe to do so beforehand. Ex. 1) Cable length: 300 mm DXT1215T-5W1U-01m(-X1) Symbol for electrical entry MNon-locking push type Push the manual override button all the way down. 2.
Do not service or attempt to remove product and machinery/ equipment until safety is confirmed. 1. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.
Do not weld an arm to the cylinder. 4) Make sure to use a speed controller and adjust it to more than 1sec. when changing from clamping to unclamping (or vice versa).
Do not bring objects that are sensitive to magnetism near the cylinder. The magnet is built into the cylinder. Do not bring magnetic disks, cards or tapes near the cylinder. Data may be lost. 5. If the cylinder is operated vertically with heavy loads, measures must be taken to prevent rapid extension of the piston rod when starting to operate in the downward direction.
Free mounting Speed controllers do not protrude from the top of the body. Top mounting Bottom mounting Side mounting Wiring and piping direction can be selected depending on mounting conditions.
Make sure that dust and/or other foreign materials do not enter the valve from the unused port (e.g. exhaust port). The grommet portion contains a breather hole for the core.
(Do not use any tools.) The initial exhaust rate is adjusted by turning the adjustment nut counterclockwise. x Opening of the initial exhaust valve (valve S) When the pilot pressure is applied to the pilot port S, the valve S is removed from the valve S seal assembly, and the valve opens the adjusted amount.
Do not use it for mounting. Otherwise, the adjustment at shipment may deviate. 792