EX500-GPN2_eng (It is recommended to ground with resistance of 100 ohms or less) M12 M12 10 14.9 Operation, Storage: 35 to 85%RH (No condensation) Operating humidity range : Seal cap is provided.
[H_1] Hysteresis of OUT1 10 25 50 100 Akihabara UDX 15F, 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021, JAPAN Phone: +81 3-5207-8249 Fax: +81 3-5298-5362 PFMB7501 [P_2] Set value of OUT2 100 250 500 1000 Accessory PFMB7102 0.5 to 0.7 Nm M4 screws (4 pcs.)
If using the product to detect very small flow rates, warm up the product for 10 to 15 minutes first. There will be a drift on the analogue output of approximate 2 to 30% immediately after supply is turn on. Within 10 minutes. Check regulators and flow adjustment valves before introducing the fluid. Pay attention to the response speed.
L/min,L Non-Reverse output Reverse output CFM x 10-2, CFM x 10-1, ft3 x 10-1, gal(US)/min, gal(US) 4 The mode in which the flow is detected and displayed, and the switch function is operating. This is the basic operating mode; and other modes should be selected for setting changes and other function settings.
Dynamic viscosity [m2/s] Viscosity [Pas] Density [kg/m3] Formulas below can be used for common units 1cP = 1mPas = 10-3Pas 1cSt = 1mm2/s = 10-6m2/s 14 Working Principle 1. When air is supplied to P1 port, it enters drive chamber A. 2. Diaphragm A moves to the left, and at the same time diaphragm B also moves to the left. 3.
(P2) 10(P2) 10(P2) 10(P2) 12(P1)10(P2) Air operated Solenoid Port VNC02 12 (P1) External pilot Bleed port External pilot 10 (P2) Bleed port External pilot Pilot exhaust Ass Ass Ass Ass y y y y VNH VNH VNH VNH () 3 3 3 3 (VNH (VNH (VNH (VNH ) ) ) ) VNH13 3 5MPa 7 VN-OMP0001 VNC VNC VNC VNC VNH VNH VNH VNH / / / / (VNC (VNC (VNC (VNC ) ) ) ) /30m /30m 0.49MPa 0.97MPa ,MPa ,MPa m/s
No.IP80-OM00019-B / / * 3-4 5 1. 5 2. 6-7 2-1 IP8000 6 2-2 IP8100 7 3. 8-9 3-1 IP8000 8 3-2 IP8100 9 4. 10-12 5. 13 5-1 13 5-2 13 6. 14 7. 15-17 7-1 16 7-2 17 7-3 17 8. 18 9. 18-20 10. 20-22 11. 23-25 11-1 23 11-2 IP8100 23 11-3 IP8000 24 11-4 24 11-5 25 12. 26 13. 27-33 2 A (ISO/IEC)(JIS)*1) *2) *1) ISO 4414: Pneumatic fluid power -General rules relating to systems ISO 4413: Hydraulic
70500mm/s 12 6-2 5,6, 12 5 5,12 10 ?
If a load that exceeds the allowable values is applied to the product, it could lead to equipment malfunction, a hazard to humans, and damage to the machinery and equipment. (10) Place an external stopper in a position away from the rotating shaft.
Decreased power-supply voltage -40- Revision history 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN Tel: + 81 3 5207 8249 Fax: +81 3 5298 5362 URL http://www.smcworld.com Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer. 2008 SMC Corporation All Rights Reserved
30 70 150 220 2,905 MHL2-32D1 120 198 318 3,820 32 20 MHL2-32D2 160 242 402 4,655 MHL2-40D 30 100 188 288 5,270 MHL2-40D1 160 246 406 6,830 40 20 MHL2-40D2 200 286 486 7,905 ) (mm) 10 16 20 25 32 40 (MPa) 0.15~0.6 0.1~0.6 () -10~60 (mm) 0.1 () (N) 0.5MPa 14 45 74 131 228 396 () 10,16,20,25 40mm 32,40 80mm 4 - 3. 3-1 3-2 3-3 1 ISO VG32 5 - 3-4 Nm mm Nm mm MHL2-10D M4X0.7 1.4 5
stroke (both sides) (mm) 10 Weight (g) 230 *Note2 *Note 2) This value excludes the weight of the attachments 2pcs : Approx. 30g and protective cover 2pcs : approx. 20g. 6 - 3-3.
mm 16 MPa 0.1~0.7 (oC) -10~50 (mm) 0.01 (c.p.m.) 120 32.7 (N) 43.5 (mm) 10 (g) 430 M8 8 (www.smcworld.com)JMHZ2 Series P .15 M8 8 7 - 3-3. 2 1 F 8 - 3-4. H 9 - 3-5. () P13P14P15 5 4 M6 85.8L 4 4 4 M3 27 17 10 - 3-6. M8 8 P .18 M8 8 () NPN PIN 1 +24V DC24V 2 3 4 5 ON/OFF 6 ON/OFF 7 8 GND DC0V M8 2 M8 1 11 - 3-7.
stroke (both sides) (mm) 10 Weight (g) 292 *Note2 *Note 2) This value excludes the weight of the attachments 2pcs : Approx. 30g and protective cover 2pcs : approx. 20g. 6 - 3-3.
Furthermore, if the cable length exceeds 5m, then it will decrease by up to 10% for each 5m.
If the product malfunctions, please return the valve as it is. 10 VT307-OMQ0002-B Revision history A Precautions on Design / Selection QZ B Renewal VS 1st printing:QV 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN Tel: + 81 3 5207 8249 Fax: +81 3 5298 5362 URL http://www.smcworld.com Note: Specifications are subject to change without prior notice and any obligation on the part of the
Light/Surge Voltage Suppressor How to Exchange Solenoid Valve, Pilot Valve Assembly Plug-in type Non plug-in type (VFR5 00) (VFR5 10) Plug-in type, Non plug-in type (VFR5 00 VFR5 10) Light/Surge voltage suppressor is not available for grommet type.
Add 10 g for conduit type, 30g for DIN terminal type, 60 g for conduit terminal type respectively. Refer to Glossary of Terms on page 6 for detail of max. operating pressure differential and max. system pressure. 10 Select an option mark in page 7 by Applicable Fluids Check List for special fluids outside of the standard.
Description Note 1 Rod cover 2 Tube cover 3 Piston 4 Piston rod 5 Bushing 6 Cushion valve 7 Speed controller valve 8 Clevis bushing 9 Hexagon socket head plug Rc1/4 10 Pin 11 Cotter pin 12 Flat washer 13 Cushion seal retainer 14 Wear ring 15 Cushion seal 16 Cushion valve seal 17 Speed controller valve seal 18 Coil scraper 19 Rod seal 20 Piston seal 21 Tube gasket 22 Cushion ring 24 Fig. 10
Function Function Terminal name Terminal name 24 V 1 1 COM+ COM+ 24 V 0 V 2 2 COM COM 0 V Pulse signal 3 3 NP+ NP+ Pulse signal Pulse signal 4 4 NP NP Pulse signal Note 1) Note 1) Pulse signal 5 5 PP+ PP+ Pulse signal Pulse signal 6 6 PP PP Pulse signal Input 7 7 SETUP SETUP Input Input 8 8 RESET RESET Input Input 9 9 SVON SVON Input Input 10 10 CLR CLR Input 11 11 12 12 Load Load 13 Output