Hydraulic Cylinders Do not use two cylinders facing one another horizontally or vertically in such a way that their piston rods strike each other. 7. When the cylinder head side contains hydraulic fluid or is in a normally pressurized condition, the applied load must not be allowed to strike the piston rod end. Avoid such applications. 8.
Note 2) 10 to 60C Ambient temperature Enclosure IEC529 Standard IP67, Immersible construction (JIS C 0920) Contact Protection Box: CD-P11, CD-P12 Lead Wire Length
Do not rotate the cover. Rotating the cover when mounting the cylinder or screwing pipe fittings into the ports may cause damage from the cover joint section. 1. Grease packs Order grease for maintenance using the order number below. Grease pack GR-X-005 (5g) Caution 1. Be careful of the snap ring springing out.
resistance 50 M or more at 500 VDC Mega (between lead wire and case) Insulation resistance Withstand voltage 1000 VAC for 1 minute (between lead wire and case) 10 to 60C Ambient temperature Enclosure IEC529 standard IP67, JISC0920 waterproof construction Contact Protection Boxes: CD-P11, CD-P12 Lead wire length
Note) When two L250 elements are used, do not discard the intermediate holder and lower element holder attached under the element, since they are reused. (Made to order elements) c Align the indentations of the case with the projections of the cover, lift the case upward by about 10mm and rotate it clockwise about 20 degrees.
Please do not attach the switch with any other screws than those already attached to the auto switch body. The operation range is shorter than that of the conventional models. If the auto switch replaces the conventional model, it may not function depending on its application because the operation range is shorter. Refer to the examples below.
At this time, take sufficient precautions since the table may move if an external force is applied. 2) Do not conduct inspection while the actuator is in operation. If inspection is unavoidable, it must never take place within the operating range of the actuator. 3) If any abnormality is found in periodic inspection, consult P/A immediately.
Provide support so that the TSUBAKI CABLEVEYOR and parts do not move freely. 2. Implement protective measures (safety cover, etc.). 3. Be sure to turn off the power and ensure that it cannot be turned on accidentally before installation, removal or maintenance of the equipment. 4.
Height tolerance Width Height Parallelism Symmetric type standardized Available with all options MXQ12-30 MXS12-30 86 0.08 46 30 0.035 80 0.2 50 32 0.2 Wide variety of adjuster options Body mounting through holes Positioning pin holes Auto switch mounting grooves Improved work piece mounting repeatability Auto switches can be mounted in grooves provided on the side of the body where they do
10,20,30,40,50,75,100,125,150 10,20,30,40,50,75,100,125,150 Stroke adjuster/shock absorber option BS BT With shock absorber at extension end* With shock absorber at retraction end* *Shock absorber option is not available for MXS6 52 Air Slide Table MXS Series Construction/Parts list, Seal list 3 6 8 9 br bs bt bp 7 2 1 bl bk bq 4 bm bn bo 5 ck cp cm cn co cq cs cr ct dk dp dn em en dr dt ek dm dq dl do
$dem B,/Bltr{ing air ft parb clebnim aDe\rv pctnt: -58'F c. less (Atnospheric pressure) aEfficiency: Lessthan 100pa icles 0.3microfts o( larger per cubic loot. allote; Use of Clean gas filter (lvernlrane) in do/(/tlstearn lin-. ,s rccommerxleo. Distributed by: ?svE' Silrc Pneumatics Inc. 301'l N. Franklin Rd. . P.O. Box 26640 . Indianapolis, lN 46226 Phone: 317-899-4440 .
Olf a lubricant is used in the system, use turbine oil type f 1 (lSO VG32). lf lubricant has been used in the system, do not cease to lubricate as the original lubricant applied during manutacturing will have been washed away.
Lubrication aTh yah,e h8 bon lub,ric.td ior ltb d nrlnubcfrirE. and dor noa lqoirr fudfiar fubdcdion in svba. ef a lubricant is used in the system, use turbine oil type #1 (lSO VG32). lf lubricant has been used in the system, do not cease to lubricate, as the original lubricant applied during manuiacturing will have been washed away. See table of suggested lubricants.
swirches Pfessrre to the side irdicated by label B rotales the shaft clockwise, pressu to the side hbeled A rciates the shaft countercl@kwise, l{cnAtB\lv3o l,rcRAroso--10() o Series:NCRAl Shaft Load fr"u lvlc&l direclion Fsa Fsb $cRAAUrgt 6 cnAtaso 110 44 44 NcRAlffl 132 44 ffi NCf,Ant8() 198 44 NCnA1otOO 220 44 In the stop position, the load can meet the value given in lhe list, please do
Not 3) Aor3 6 15 (basic typ) ar tully pod6d and do not rqunettl x150 optton. Specifications
Barb fitting Barb elbow Barb elbow (H) Surface treatment (Color) Fitting marking for applicable tube material Connection Tube Soft nylon tube Polyurethane tube Electroless nickel plating (Silver color) M3 Electroless nickel plating (Silver color) Nylon tube 1 8 R(PT) , M5 Electroless nickel plating (Black color) [Except stud] Soft nylon tube Polyurethane tube M-5E, M-5ER, M-5M do not have
(between lead wire and case) 1000VAC for 1min (between lead wire and case) Withstand voltage Ambient temperature 10 to 60C enclosure IEC529 standard IP67, JISC0920 watertight construction Contact Protection Boxes/ CD-P11, CD-P12 Lead Wire Length
Load connection fittings should be designed so that they do not exceed the weights given in the table below.
Do not connect the white wire of the sensor to c of the display unit. View A Terminal block number 4 3 2 1 1 2 3 4 5 6 7 8 8 7 6 5 Series PF2D For Deionized Water and Chemicals Digital Flow Switch Functions/PF2D Refer to the operation manual how to set and to operate. Output types Flow rate measurement selection Real-time flow rate and accumulated flow rate can be selected.
Thanks to a tool-free module press-in connector, all you need to do is to simply snap-in the lead wire and lock it! Crimping tools are not required. The connection cable is a halogen-free heavy-duty cord.