ISO Cylinder Do not service or attempt to remove product and machinery/ equipment until safety is confirmed. 1. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.
Do not weld an arm to the cylinder. 4) Make sure to use a speed controller and adjust it to more than 1sec. when changing from clamping to unclamping (or vice versa).
Do not use a lubricator on the inlet side of the product, as the bleed mechanism can malfunction. Caution 1. For emergency action in the event of setting failure or leakage from the relief port, refer to Troubleshooting in the Operation Manual of the product. Piping Warning Air Preparation Equipment 1.
Do not bring objects that are sensitive to magnetism near the cylinder. The magnet is built into the cylinder. Do not bring magnetic disks, cards or tapes near the cylinder. Data may be lost. 5. If the cylinder is operated vertically with heavy loads, measures must be taken to prevent rapid extension of the piston rod when starting to operate in the downward direction.
Free mounting Speed controllers do not protrude from the top of the body. Top mounting Bottom mounting Side mounting Wiring and piping direction can be selected depending on mounting conditions.
Make sure that dust and/or other foreign materials do not enter the valve from the unused port (e.g. exhaust port). The grommet portion contains a breather hole for the core.
(Do not use any tools.) The initial exhaust rate is adjusted by turning the adjustment nut counterclockwise. x Opening of the initial exhaust valve (valve S) When the pilot pressure is applied to the pilot port S, the valve S is removed from the valve S seal assembly, and the valve opens the adjusted amount.
When using the male thread mounting type product, do not loosen the bottom nut shown in the figure below. (The bottom nut is intended to secure the connection between the bracket for the adapter connection and the male thread.) PD3 Circuit without release valve (Usage example of vacuum connection) V V PD2 PD2 Supply valve EXH. P Pressure sensor Do not loosen this nut.
Do not use it for mounting. Otherwise, the adjustment at shipment may deviate. 792
Do not disassemble the product. Once the product is disassembled and reassembled, it will not be able to satisfy the original performance. 4. When piping, do not get the pad side and vacuum generator side of the product the wrong way round. (Refer to Fig. 1.)
Do not drop, hit or apply excessive shock to the product. Even if the body is not damaged, the internal components may be damaged, leading to a malfunction. Wiring/Piping Warning 1. Power supply required to the product is 24 VDC and 1 A.
Do not use this aftercooler in an area that has viscous dust (electrostatic paint powder, oily particles, etc.). If it must be used under such conditions due to unavoidable circumstances, please contact SMC beforehand.
Do not make any upward angles in drain line.
Do not use this aftercooler in an area that has viscous dust (electrostatic paint powder, oily particles, etc.). If it must be used under such conditions due to unavoidable circumstances, please contact SMC beforehand.
Do not allow the weight of piping to be applied directly to the air dryer. HA AT ID Avoid installation on moving objects like trucks, ships, and so forth. Drain Tube AMG Caution AFF A polyurethane tube of 10mm outer diameter is provided as the drain tube for IDFS6E to 11E and IDUS3E to 6E. Use this tube to discharge drainage. Do not use the drain tube in an upward direction.
Free mounting Speed controllers do not protrude from the top of the body. Top mounting Bottom mounting Side mounting Wiring and piping direction can be selected depending on mounting conditions.
Therefore, do not touch its exterior surface because it could be very hot, depending on the energizing conditions.
Do not scratch or gouge the piston rod of the actuating cylinder, as this could damage the rod seal and lead to air leaks. The same applies to the guide shaft. 3. Make sure not to apply shocks or excessive moment to the slide block of the ball bushing type. 4.
This is a legacy product. Please contact us for the latest version.sales@ocaire.com, MANIFOLD, VALVE, VV2Q* MANIFOLD VQ 2-PORT, 2J, VV2Q* NO SIZE RATING, 1.90148 lb