Valve Single Unit One-touch fitting for 5/16" Note 1) P and R ports cannot be changed. Note 2) Use caution that O-rings must be free from scratches and dust.
Polyurethane tubing: Series TU, Nylon tubing: Series T, and Soft nylon tubing: Series TS can also be used. However, the degree of clean performance will be reduced.
The write prohibited setting parameter (Fn010) must be set to Write permitted (P.0). The main circuit power supply must be ON. All alarms must be cleared. The hardwire baseblock (HWBB) must be disabled. The servomotor power must be OFF. There must be no overtravel. The test without a motor function must be disabled (Pn00C.0 = 0).
It must be operated manually. 0.2 0.2 0.1 0.1 00 25 50 75 100 125 150 00 1000 2000 3000 Flow rate L/min (ANR) Flow rate L/min (ANR) AR20 Rc 1/4 AR40-06 Rc 3/8 0.6 0.6 0.5 0.5 Outlet pressure MPa Outlet pressure MPa 0.4 0.4 0.3 0.3 0.2 0.2 Caution 1. Be sure to unlock the knob before adjusting the pressure and lock it after setting the pressure.
Load factor: ((Load weight x 9.8)/Theoretical force) x 100% Conditions Series CJ2 Series CM2 6 x 1 m AS3301F-06 12 x 1 m AS4001F-12 AN200-02 AS2301F-06 AN110-01 Series MB/CA2 Series CJ2 Series CM2 Series MB/CA2 Body ported Tubing bore x Length Speed controller Silencer Base mounted Tubing bore x Length Speed controller Silencer AN200-02 AN3301F-06 AS1301F-06 6 x 1 m AS3001F-06 SYJ7120-01
Polyurethane tubing: Series TU, Nylon tubing: Series T, and Soft nylon tubing: Series TS can also be used. However, the degree of clean performance will be reduced.
Polyurethane tubing: Series TU, Nylon tubing: Series T, and Soft nylon tubing: Series TS can also be used. However, the degree of clean performance will be reduced.
Please consult SMC if this is not acceptable. (4) Set range of outlet pressure shall be 85% or less of the inlet pressure.
-01-06-X214 AS2001F-06-X214 AS2301F-01-06-X214 DREC32 AS2201F-01-06-X214 AS3001F-08-X214 AS2301F-01-06-X214 REC40 AS3201F-02-08-X214 AS3001F-08-X214 AS3301F-02-08-X214 -X Use the recommended speed controllers.
-01-06-X214 AS2001F-06-X214 AS2301F-01-06-X214 DREC32 AS2201F-01-06-X214 AS3001F-08-X214 AS2301F-01-06-X214 REC40 AS3201F-02-08-X214 AS3001F-08-X214 AS3301F-02-08-X214 -X Use the recommended speed controllers.
-01-06-X214 AS2001F-06-X214 AS2301F-01-06-X214 DREC32 AS2201F-01-06-X214 AS3001F-08-X214 AS2301F-01-06-X214 REC40 AS3201F-02-08-X214 AS3001F-08-X214 AS3301F-02-08-X214 -X Use the recommended speed controllers.
Also, the surge pressure must be under the maximum operating pressure.
10-ASD330F-01-08 10-ASD230F-M5-06 2.
Note 2) On the AMC220, an R 1/4 fittinng can be attached by removing the drain cock. (It be comes the drain piping type.
How to Order KQ 2 H 06 U01 Made to Order Refer to page 90 for details.
If multi-pads are used with only one ejector and one pad does not make complete adsorption, then vacuum pressure will be lost. Subsequently other pads will be unable to complete adsorption.
The load must be guided by other means. The mounting fittings for the load should be designed to meet the weight limits shown in this table.
This product cannot be used to hold a stop position for an extended period of time. Pilot check valves and actuators are not guaranteed for zero air leakage. Therefore, it is sometimes not possible to hold a stop position for an extended period of time. In the event that holding for an extended time is necessary, a mechanical means for holding should be devised. 3.