CQSY/CQ2Y/CM2Y/CG1Y/CA2Y .-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com 20 25 32 40 0.02 RHC 50 63 80 100 0.01 MK(2) 0 0 10 20 30 40 60 50 70 80 90 100 RS Q G Bore size mm RS H A (Measurement based on JIS B8377) RZQ MI W S CEP1 Stable operation possible even at a low speed of 5 mm/s (Measurement based on JIS B 8377) Sliding
Horizontal and lateral Mounting Vertical Mounting 50 RS H A 2.
-485 Table 8-13 Serial RS-485 Item Specification Connector No.
CHKDB CHKGB Double acting, Single rod 40 10 16 CX 50 5, 10, 15, 20, 25, 30 35, 40, 45, 50, 75 100 63 CY 80 100 MQQ M CHKDB CHKGB RHC MK(2) RS Q G RS H A For details, refer to the catalog CAT. E111.
RS Q G Basic type: RBL1411, RBL1412, RBL2015, RBL2725 With cap: RBLC1411, RBLC1412 RBLC2015, RBLC2725 RS H A Other dimensions are the same as the basic type.
RS Q G Valve A If the converter is positioned lower than the cylinder: RS H A Drain port (Piping port) After filling with oil as described in step 4 above, close the oil filler plug. Then, introduce air pressure of approximately 0.05 MPa into the converters air port to push the oil into the cylinder.
Cooling capacity A : RS-485 001 : 140W B : RS-232C 003 : 320W AC100 240V Water Cooled 3.2 Manufacturing years method of display SERIAL No. M Q 0001 Serial No.
How to Order Valve Manifold Assembly Nil S R RS Internal pilot Internal pilot / Built-in silencer External pilot External pilot / Built-in silencer Ordering example (SS5J3-60SVl-l) There is no need to enter anything when the SUP/EXH block mounting position M is selected. For built-in silencers, the 3/5(E) ports are plugged.
Fig.3-2 RS-232C connector connection 3.3 Communication specification Table 3.3-1 Serial communication specification Item Specification Connector type (for the product) D-sub9P type Female connector Standard Select from EIA RS-485 / RS-232C Circuit type Half duplex Transmission type Start-stop Protocol Modbus terminal *1 Terminal resistance None Default setting *1 Refer to Modicon Co. protocol
MQQ M RHC L N 40 100 JN 1 W D CVS1 Without auto switch MK(2) L 100 Y7BW N 40 JN 1 W D CDVS1 With auto switch RS Q G Suffix for cylinder RS H A Built-in magnet J K N R H Nil Nylon tarpaulin Heat resistant tarpaulin Without cushion With cushion on rod end With cushion on head end With cushion on both ends Solenoid valve voltage Rod boot Mounting style 1 2 5 9 100 VAC (50/60 Hz) 200 VAC
Q G RS H A RZQ MI W S Non-lube type Long stroke type CEP1 CE1 Component Parts CE2 Note Material Material No.
MK(2) Eccentric slide Long service life (with dustproof cover) RS Q G Rotating angle5 Operating range RS H A Center of sphere RZQ Operating range Axial center MI W S Series Variations CEP1 Series Operating pressure Pneumatic cylinder Hydraulic cylinder Applicable bore size (mm) Mounting Page CE1 CE2 Standard Series JA 6, 10, 15, 20 25, 32, 40, 50 63, 80, 100, 125 140, 160 ML2B Basic style
(Page 20) Communications RS-232C/RS-485 Weight Approx. 20 kg Approx. 21 kg Accessories Power supply connector, Operation Manual Power supply cable should be ordered as an option (sold separately, page 22) or prepared by the user.
RHC Brake valve Actuating valve MK(2) RS Q G RS H A Stroke reading cylinder with brake (CE2) Extension cable RZQ Sensor cord Head side cylinder port Controller: Series CEU2 MI W S External equipment (PLC, etc.)
RS Q G RS H A Stroke reading cylinder with brake (CE2) Extension cable RZQ Sensor cord Head side cylinder port Rod side cylinder port Controller: Series CEU2 MI W S External equipment (PLC, etc.)
MK(2) Eccentric slide Long service life (with dustproof cover) RS Q G Rotating angle5 Operating range RS H A Center of sphere RZQ Operating range Axial center MI W S Series Variations CEP1 Series Operating pressure Pneumatic cylinder Hydraulic cylinder Applicable bore size (mm) Mounting Page CE1 CE2 Standard Series JA 6, 10, 15, 20 25, 32, 40, 50 63, 80, 100, 125 140, 160 ML2B Basic style
(Example) Bolt M5 x 110l (Two bolts are necessary per cylinder) RS Q G RS H A RZQ Rod side mounting Head side mounting MI W S CEP1 CE1 CH CR CE2 Attached B-type washer D D ML2B C J G5-S CV MVGQ C 50, 63 CC Note) Use the attached washer when inserting the bolt from the rod side.
Application Classification Initial value (default setting) 1 COM of contact input signal Input 2 Contact input signal 1 Input Run/Stop signal 3 Contact input signal 2 Input External switch signal 4 (None) 5 RS-485 Communication SD+ 6 RS-485 Communication SD7 RS-485 Communication SG 8 (None) 9 Contact output signal 1 Output Operation status (A contact) (normally open) 10 COM of contact output