Two Hand Control Valve Mandrel = LD 2d 1 x 100 Here, : Deformation ratio (%) d: Tube diameter (mm) L: Measured length (mm) D: Mandrel diameter (mm) (Twice against the minimum bending radius) Test temperature: 20 5C Relative humidity: 65 5% Air Supply Warning 5.Do not use fluids other than specified. The only fluid that can be used is air. 1. Use clean air.
If the fluid temperature is 5C or less, the moisture in the circuit could freeze, causing damage to the seals and equipment malfunction. Therefore, take appropriate measures to prevent freezing. For compressed air quality, refer to the Product Selection Guide. 5.
If the fluid temperature is 5C or less, the moisture in the circuit could freeze, causing damage to the seals and equipment malfunction. Therefore, take appropriate measures to prevent freezing. For compressed air quality, refer to the Product Selection Guide. 5.
Buffer stroke 40 50 63 80 100 125 Series ZPT ZPX Related 25 50 75 100 Equipment Pad Material and Characteristics Characteristics Operating temperature range (C) Oil resistance gasoline Oil resistance benzol Base resistance Acid resistance Weatherability Ozone resistance Abrasion resistance Waterproof Solvent resistance (Benzene, toluene) Durometer HS (5C) Material 50C 50C 50C 60C 60C NBR
Buffer stroke 25 50 75 100 40 50 63 80 100 125 Series ZPT ZPX Pad Material and Characteristics : Little or no influence : Can be used depending on conditions X: Not suitable Characteristics Operating temperature range (C) Oil resistance gasoline Oil resistance benzol Solvent resistance (Benzene, toluene) Durometer HS (5C) Base resistance Acid resistance Abrasion resistance Ozone resistance
Buffer stroke 25 50 75 100 40 50 63 80 100 125 Series ZPT ZPX Pad Material and Characteristics : Little or no influence : Can be used depending on conditions X: Not suitable Characteristics Operating temperature range (C) Oil resistance gasoline Oil resistance benzol Solvent resistance (Benzene, toluene) Durometer HS (5C) Base resistance Acid resistance Abrasion resistance Ozone resistance
Moisture in circuits can freeze at 5C or below, causing damage to Orings, and malfunction. Consider measures to prevent freezing. The installation of an air dryer is recommended to remove drainage and moisture from circuits. Furthermore, even though the ambient temperature range remains within specifications, do not operate in locations where there are abrupt temperature changes. 2.
If the fluid temperature is 5C or below, the moisture in the circuit could freeze, causing damage to the seals and leading to equipment malfunction. Therefore, take appropriate measures to prevent freezing. Refer to SMC's Air Cleaning Equipment catalog for further details on compressed air quality. Operating Environment Warning 1.
Take measures to prevent freezing, since moisture in circuits can be frozen under 5C, and this may cause damage to seals and lead to malfunction. Refer to SMCs Air Cleaning Equipment catalog for further details on compressed air quality. Wrapping direction Expose approx. 2 threads Pipe tape 114 Actuator Precautions 3 Series MY1 Operating Environment Maintenance Warning Warning 1.
Take measures to prevent freezing when below 5C, since moisture in circuits can freeze and cause damage to seals and lead to malfunctions. Refer to SMCs Air Preparation System catalog for further details on compressed air quality. Caution 1. Filter drainage Drain out condensate from air filters regularly. Operating Environment Warning 1.
For MY2H16, H unit At temperatures of 5C or less, take measures to prevent freezing, since moisture in circuits can be frozen and this may cause damage to seals and lead to malfunction. Refer to SMCs Best Pneumatics vol.4 catalog for further details on compressed air quality.
Take measures to prevent freezing, since moisture in circuits can be frozen under 5C, and this may cause damage to seals and lead to malfunction. Refer to SMCs Air Cleaning Equipment catalog for further details on compressed air quality. Maintenance Warning 1. Removal of equipment, and supply/exhaust of compressed air.
Take measures to prevent freezing when 5C or less, since moisture in circuits can freeze and cause damage to seals and lead to malfunctions. Piping Caution 1. Preparation before piping Before piping is connected, it should be thoroughly blown out with air (flushing) or washed to remove chips, cutting oil, and other debris from inside the pipe. 2.
Take measures to prevent freezing since moisture in circuits can freeze at, or below 5C, and this can cause damage to seals and lead to malfunctions. Refer to SMCs Air Cleaning Equipment catalog for further details on compressed air quality. Warning 1. Adjust the speed gradually increasing from a low speed to the desired setting.
Replace the adsorbent according to color of the indicator. 1 4 1 2 1 2 3 4 520 615 850 961 45 45 75 75 9 9 9 9 120 120 170 170 95 95 95 95 59.5 59.5 88 88 128.5 128.5 243.5 243.5 59.5 59.5 66.5 66.5 134.5 134.5 183 183 222 222 302 302 Dew point temperature (Atmospheric pressure) 30C or less 18C 10C 5C Color of indicator ID300 ID400 ID600 Dark blue Light blue Light pink air, the capillary
Replace the adsorbent according to color of the indicator. 1 4 1 2 1 2 3 4 520 615 850 961 45 45 75 75 9 9 9 9 120 120 170 170 95 95 95 95 59.5 59.5 88 88 128.5 128.5 243.5 243.5 59.5 59.5 66.5 66.5 134.5 134.5 183 183 222 222 302 302 Dew point temperature (Atmospheric pressure) 30C or less 18C 10C 5C Color of indicator ID300 ID400 ID600 Dark blue Light blue Light pink air, the capillary
Take measures to prevent freezing, since moisture in circuits will be frozen under 5C, and this may cause damage to seals and lead to malfunction. Refer to SMCs Air Cleaning Equipment catalog for further details on compressed air quality.
Take measures to prevent freezing, since moisture in circuits can be frozen below 5C, and this may cause damage to seals and lead to malfunction. Refer to SMCs Best Pneumatics vol. 4 for further details on compressed air quality. Wrapping direction Expose approx. 2 threads Pipe tape Cushion Caution Operating Environment 1. Readjust using the cushion needle.
For more information, refer to page 6-8-16. 6-8-58 59 Series CA2WH Air-hydro Cylinder: Air-hydro Type Double Acting, Double Rod Specifications Type Air-hydro Fluid Turbine oil Action Double acting Proof pressure 1.5 MPa Maximum operating pressure 1.0 MPa 0.16 Mpa Minimum operating pressure 0.5 to 300 mm/s Piston speed CJ1 5C to 60C Ambient and fluid temperature CJP Without Cushion Thread
Take measures to prevent freezing when below 5C, since moisture in circuits can freeze and cause damage to seals and lead to malfunctions. For details on the quality of compressed air mentioned above, refer to SMCs Best Pneumatics catalog vol. 14. 5. Do not use until you verify that the equipment can operate properly.