Air Cylinder Series MB The purpose of an air cushion is not to reduce the speed of a piston as it nears the stroke end.
10-20-59 With built-in OFF-delay timer (200 ms) CE1 D-G5NTL D-F7NTL D-F5NTL D-M5NTL/M5PTL 10-20-60 Grommet Band Solid state switch With timer 10-20-61 Grommet Rail CE2 10-20-62 Grommet Tie-rod 10-20-63 Grommet Direct ML2B Possible to use in an environment where disturbance magnetic fields are generated.
For an exterior dimension diagram to identify the mounting support types, refer to p.3.1-21 to 3.1-24 as the dimensions are identical to those of standard.
Model HTB 1 8 Rc CY1S20 CY1S25 CY1L25 CY1S32 CY1L32 CY1S40 CY1L40 20 20 7.5 20 20 7.5 1 8 Rc 20 23 8.2 24 24 7.5 1 8 Rc 26.5 26.5 8.2 25 25 8 1 4 Rc 30.5 30.5 11 Dimensions except mentioned above are the same as standard type of Series CY1B. Refer to page 8-15-24.
If the input or output size is an odd number, add 1 byte, to make it an even number of bytes. The I/O map is shown with the following unit configuration as an example.
.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com 4 Electric Actuator with Integrated Guide Series LTF Lead screw lead mm Mounting orientation Motor type Series Page Model Guide type Ground ball screw Rolled ball screw 6 10 20 10 20 10 20 10 20 6 10 20 10 20 10 20 10 20 LTF6 LTF8 LTF6 LTF8 LTF6 LTF8
20 4 18 to 36 10 to 200 10 to 20 1.5 10 to 20 20 to 400 20 3 17.5 to 35 10 to 200 10 to 20 0.5 5 to 7.5 20 to 400 20 1 7.5 to 11 10 to 200 10 to 20 Servo Motor (24 VDC)/Step Motor (Servo/24 VDC) Actuator specifications Electric specifications Lock unit specifications Pushing force 50 to 100% [N] Note 2) LES LESH LECA6 LECP6 LEC-G LECP1 LECPA Speed [mm/s] Pushing speed [mm/s] Max. acceleration
Environment at an altitude of 1000 meters or higher Heat radiation and withstand voltage will decrease. Contact SMC for details. (2) Do not use in an environment where the product is directly exposed to liquid, such as cutting oils.
Same as cushion seal A except for 20, 25 standard strokes Steel ball B Carbon steel 21 Cushion seal B Urethane 57 Tooth ring Stainless steel 22 Damper Urethane Cushion ring gasket A NBR 58 23 Same as cushion ring gasket A except for 20, 25 standard strokes C type snap ring for taper ring Carbon steel 24 Cushion ring gasket B NBR 59 C type snap ring for unlocking cam shaft Carbon steel 25
Depending on the external switch output type, wire the switch to the communication connector for contact input / output (which is included as an accessory) as shown below. Mount the ferrite core (3 turns), which is included as an accessory. This is an example of wiringRefer to the Communications Operation Manual for more details.
Disable Does not generate an error. Enable Generates an error. 1 -10..10 V -5..5 V -20..20 mA 0..10 V 0..5 V 1..5 V 0..20 mA Analogue input range [Range] Set the analogue input device range per channel. Selects the analogue input range. -10..10 V 2 [Measurement Range] 4..20 mA Offset binary Offset binary. Analogue data format [D_Format] Configure analog data format per unit.
Available only as an Assembled Item. Please see below for How to Order Piston Rod Assembly. Available only as an Assembled Item. Please see below for How to Order Piston Rod Assembly. Available only as an Assembled Item. Please see below for How to Order Piston Rod Assembly. Available only as an Assembly Item. Please see Rod/Head Cover.
When using as a stopper, select a model with a stroke of 30mm or less for bore sizes 20 and 25, and 50mm or less for bore sizes 32 to 100.
When using as a stopper, select a model with a stroke of 30mm or less for bore sizes 20 and 25, and 50mm or less for bore sizes 32 to 100.
Pad Caution Guide for drop prevention Provide an auxiliary device (example: a guide for preventing the workpieces from dropping) as necessary. Mounting Position As a rule, the unit must be installed horizontally.
Pad Caution Guide for drop prevention Provide an auxiliary device (example: a guide for preventing the workpieces from dropping) as necessary. Mounting Position As a rule, the unit must be installed horizontally.
Pad Caution Guide for drop prevention Provide an auxiliary device (example: a guide for preventing the workpieces from dropping) as necessary. Mounting Position As a rule, the unit must be installed horizontally.
Combination Symbol: K2 Combination Symbol: K7 An N.C. solenoid valve is used as the supply valve. Also, an external 2 port valve (vacuum valve) must be provided to serve as the vacuum release valve. An air operated N.O. valve is used as the supply valve. An N.C. solenoid valve is used for the vacuum release valve.
As a result, the inside of the bowl q is shut off from the outside air. Therefore, even if there is an accumulation of condensate in the bowl q, it will not drain out.
Note 2) 4 to 20 mA DC is not possible with the 2-wire type. Power supply voltage (24 VDC or 12 to 15 VDC) is required. Note 3) Value for the state with no over current circuit included. If an allowance is provided for an over current circuit, the input impedance varies depending on the input power supply. This is 350 or less for an input current of 20 mA DC.