NCQ8 075 (3/4") NCQ8B075-S-PS 106 (1-1/16") NCQ8B106-S-PS Piston seal is included. 150 (1-1/2") NCQ8B150-S-PS 200 (2") NCQ8B200-S-PS 250 (2-1/2") NCQ8B250-S-PS With auto switch Here is the typical, cross-sectional construction.
64 74 16 20 22 30 36 46 28 28 28 30 36 46 43.4 48 59.4 71.4 86 105.4 CS1 Up to 300 Up to 300 Up to 300 CS2 Up to 300 Up to 300 Use a thin wrench when tightening the piston rod.
Hs T (mm) Symbol BX BY D F GA GB L M N S T W Wc Ws Z ZZ Hs IA K Bore size 40 56 54 16 44 77 10 55 M12 x 1.5 86 112.5 57 5 39 27.5 114 228 46 47 14 50 64 64 20 55 78.5 10 58 M16 x 1.5 87.5 117 60 7 41 33 118.5 232.5 50 58 17 63 74 74 20 69 82 12 58 M16 x 1.5 91 120.5 67 5.5 48 39 122 236 56 72 17 12 Series CLK1 Clamp Cylinder with Lock Accessory Dimensions (mm) Single Knuckle Joint Double
The piston speed may exceed the maximum operating speed of 500mm/s if the piping is directly connected to the cylinder. Please use speed controllers by SMC to adjust the piston speed so that it will not exceed 500mm/s.
Please contact SMC for a specification sheet when placing an order. Shaft Pattern Sequencing II -XA31 to XA47 Applicable shaft type: J, K, S, T, Y Shaft type CRB2 J K Refer to CRBU2 S page 11-2-8.
Please contact SMC for a specification sheet when placing an order. Shaft Pattern Sequencing II -XA31 to XA47 Applicable shaft type: J, K, S, T, Y Shaft type CRB2 J K Refer to CRBU2 S page 11-2-8.
Please contact SMC for a specification sheet when placing an order. Shaft Pattern Sequencing II -XA31 to XA47 Applicable shaft type: J, K, S, T, Y Shaft type CRB2 J K Refer to CRBU2 S page 11-2-8.
In addition, by connecting an input block a maximum of 32 sensor signal inputs are possible. Input block This is an expansion block which connects to an SI unit to perform sensor input from auto switches, etc.
Perform an echo back test for the controller with controller ID:1.
After 1.6 s Blinking After 0.2 s When an alarm or warning also occurs during the test operation, the decimal point on the first digit will blink as follows. After 0.8 s After 0.8 s Blinking Blinking After 0.2 s (4) Start operation with the PC. -21- 5.2 JOG Mode JOG operation can be executed without host command.
Bore size (mm) 40 10 Auto switch model 50 63 80 100 D-A5/A6 D-A59W D-F5/J5 D-F5W/J59W D-F5F/F5NTL BT-04 BT-04 BT-06 BT-08 BT-08 1 100 D-A3/A44 D-G39/K39 D-B5/B64 D-B59W D-G5/K59 D-G5W/K59W D-G59F D-G5NTL 1000 500 BDS-04M BDS-05M BMBI-063 BMBI-080 BMBI-100 Maximum speed (mm/s) (Example) Find the upper limit of rod end load when an air cylinder of 63 is operated at 500 mm/s.
Configuration 1 master : 1 thermo-chiller 2 2 R D R D 3 3 S D S D 5 5 S G S G Master This product Do not connect any wire to other PIN numbers. Fig. 3-10 Connection of RS-232C 3.3 Installation HRS Series 3-16 HRX-OM-R016 Chapter 3 Transport and Setting Up 3.4 Piping Connect piping firmly.
The only possible way in that case is the use of an external stopper.
Order Made Note) When an auto switch is installed at an intermediate position of a type with auto switch, keep the maximum piston speed at 300 mm/s or below to ensure operation of relays or other devices.
(ANR)) Type S 22 38 54 62 84 ZX Type L 42 52 74 105 88 Air consumption (l/min (ANR)) 46 78 95 185 150 ZR Maximum vacuum pressure L: 53 kPa S: 84 kPa ZM Built-in silencer, Manifold common or individual exhaust Exhaust release (Ejector exhaust) ZH Valve unit ZR1-V ZU Component equipment Supply valve (Pilot type)/Release valve (Pilot type) Courtesy of Steven Engineering, Inc.-230 Ryan Way, South
Operation stop Combination Symbol: D1 Combination Symbol: D4 An N.C. solenoid valve is used for the vacuum release valve. An external supply valve must be provided. An external valve must be provided to serve as the supply valve. An air operated N.C. valve is used for the vacuum release valve.
or less 3% F .S. or less Repeatability Note 1) 2% F .S. or less 1% F .S. or less Temperature characteristics 2% F.S. or less (15 to 35C based on 25C), 3% F .S. or less (0 to 50C based on 25C) Pulse output, N channel, open drain, output for display unit PF2W3.
Cautions for use in an interlock circuit When an auto switch is used for an interlock signal requiring high reliability, devise a double interlock system to avoid trouble by providing a mechanical protection function, or by also using another switch (sensor) together with the auto switch. Also perform periodic maintenance inspections and confirm proper operation. 9.
Body Brass Body S. S.
Cautions for use in an interlock circuit When an auto switch is used for an interlock signal requiring high reliability, devise a double interlock system to avoid trouble by providing a mechanical protection function, or by also using another switch (sensor) together with the auto switch. Also perform periodic maintenance inspections and confirm proper operation. 9.