Cooling Capacity: 150, Thread Type: N [NPT (w/Rc-NPT Conversion Fitting)], Power Supply: 46 [3-phase 380 to 415 VAC (50/60 Hz); 3-phase 460 to 480 VAC (60 Hz)], Option 1: -, UL Certification: -, Option 2: -
Cooling Capacity: 100, Thread Type: N [NPT (w/Rc-NPT Conversion Fitting)], Power Supply: 46 [3-phase 380 to 415 VAC (50/60 Hz); 3-phase 460 to 480 VAC (60 Hz)], Option 1: -, UL Certification: -, Option 2: -
Cooling Method: Air-cooled Refrigeration, Pipe Thread: N [NPT (w/Rc-NPT Conversion Fitting)], Power Supply: 46 [3-phase 380 to 415 VAC (50/60 Hz); 3-phase 460 to 480 VAC (60 Hz)], Option: -
1 Do not use in an atmosphere containing an inflammable gas or explosive gas. Use in such an atmosphere is likely to cause a fire or explosion. This system is not explosion-proof. Caution 1. Select the proper type of enclosure according to the environment of operation.
Install an air filter. Install an air filter at the upstream side of valve. Select an air filter with a filtration degree of 5 m or finer. Maintenance 2. Install an aftercooler, air dryer or water droplet separator, etc. Compressed air that contains a large amount of drainage can cause malfunction of pneumatic equipment.
The pre-load type requires an air-hydro converter (Series CCT).
It may cause an accident or malfunction.
/Flange Rod end width across flats 10 10 21 21 46 46 Data Part no.
Provided with an end lock mechanism An end lock is also available, which maintains the cylinders original position even if the air supply is interrupted.
46 119.2 58 136 173 MORE DIMENSIONS S E E N E X T P A G E Courtesy of Steven Engineering, Inc. !
Note 1) This cylinder cannot perform an intermediate stop using an air pressure circuit in vertical operation. In this case, an intermediate stop can be performed only by using an external stopper, etc. Made-to-order products should be considered, too, depending on an operating environment, etc.
Otherwise, it may cause an electric shock. Do not operate switches with wet hands. Otherwise, it may cause an electric shock. The cables should not be damaged, stressed, loaded, or pinched. Otherwise, it may cause an electric shock. During power-on or operation, do not open the front cover of the s driver. Otherwise, it may cause an electric shock.
Operate in an ambient temperature range between 0C and 50C. 3. Operate in an ambient humidity range between 35% to 85% (with no condensation).
odd number, an even number that is one larger than this odd number is used for the calculation. 4: When n is an odd number, an even number that is one larger than this odd number is used for the calculation.
The values in these tables indicate the maximum stroke that can be used in a situation when air is being supplied while the cylinder is stopped in an intermediate position by a) an external force acting on the piston rod and/or by b) an external stopper.
If an intermediate stop is performed by an external stopper, be careful of ejection when restarting. If lurching occurs, damage can result. If a slide table is stopped at an intermediate position by an external stopper and then moved forwards, after the slide table is returned to the back to retract the stopper, supply pressure to the opposite port to operate the slide table. 3.
) 46 (46) 10 to 100 117 (127) 127 (127) 107 (127) 10 43.5 (53.5) 53.5 (53.5) 140 (150) 150 (150) 130 (150) 12 53 (63) 63 (63) Note 1) ( ): Denotes the dimensions with auto switch.
. 8-7 8.1.8 Communication specification . 8-7 8.2 Outline dimensions . 8-8 8.2.1 HRS100/150-A-20/40/46. 8-8 8.2.2 HRS100/150-W-20/40/46. 8-9 8.3 Flow diagram . 8-10 8.3.1 HRS100/150-A-20/40/46. 8-10 8.3.2 HRS100/150-W-20/40/46. 8-11 8.4 Cooling capacity . 8-12 HRS Series HRX-OM-S004 Contents 8.4.1 HRS100-A-20/40/46. 8-12 8.4.2 HRS150-A-20/40/46. 8-12 8.4.3 HRS100-W-20/40/46. 8-13 8.4.4 HRS150
After tightening by hand, the barb fitting type should be tightened by an additional 1/4 rotation using an appropriate wrench. 2. After tightening by hand, the barb elbow type should be tightened by an additional 1/2 rotation using an appropriate wrench. 2) M5 1. After tightening by hand, the barb fitting type should be tightened by an additional 1/6 rotation using a suitable tool. 2.