MK An area in which fluids such as cutting oil splash on the piston rod. 2. An area in which foreign matter such as particles, cutting chips, dust, or spatter is present. 3. An area in which the ambient temperature exceeds the operating range. 4. An area exposed to direct sunlight. 5. An environment that poses the risk of corrosion.
Take measures to ensure air quality, such as by installing an aftercooler, air dryer, or water separator. Compressed air that contains a large amount of drainage can cause the malfunction of pneumatic equipment, such as valves. Therefore, take appropriate measures to ensure air quality, such as by providing an aftercooler, air dryer, or water separator. 4.
Compatible with chemicals such as acids, bases and ultra DI water.
46 LB 27 31 36 46 46 LA 35.5 41 47 62 62 LA 35 41 46 62 62 L 52.5 59 67 81 84 L 52.5 59 67 81 84 ZZ 115.5 127 137 171 175 Model MU25 MU32 MU40 MU50 MU63 Model MU25 MU32 MU40 MU50 MU63 Applicable pin 8 10 10 14 14 9 11 13 16 16 8 10 10 14 14 9 11 13 16 16 +0.058 0 +0.058 0 +0.058 0 +0.070 0 +0.070 0 0.2 0.4 0.2 0.4 0.2 0.4 0.2 0.4 0.2 0.4 +0.058 0 +0.058 0 +0.058 0 +0.070 0 +0.070 0 +0.2
46 LB 27 31 36 46 46 LA 35.5 41 47 62 62 LA 35 41 46 62 62 L 52.5 59 67 81 84 L 52.5 59 67 81 84 ZZ 115.5 127 137 171 175 Model MU25 MU32 MU40 MU50 MU63 Model MU25 MU32 MU40 MU50 MU63 Applicable pin 8 10 10 14 14 9 11 13 16 16 8 10 10 14 14 9 11 13 16 16 +0.058 0 +0.058 0 +0.058 0 +0.070 0 +0.070 0 0.2 0.4 0.2 0.4 0.2 0.4 0.2 0.4 0.2 0.4 +0.058 0 +0.058 0 +0.058 0 +0.070 0 +0.070 0 +0.2
Neoprene a soft synthetic rubber used as an insert material on certain types of Freons. Power Consumption the number of watts a solenoid valve draws when it is energized. Nordel a soft synthetic rubber used as an insert material on certain water and steam applications. Pressure is a potential force used as a propellant of air or fluid.
Actuator effective torque (3 to 5) x Tf ( If the mass of the clamp itself in the drawing below is considered in the calculations, it should be regarded as an inertial load. ) ( If the mass of the lever itself in the drawing below is considered in the calculations, it should be regarded as an inertial load. ) (Example) (Example) Accelerating torque calculation Ta = I (Nm) Friction coefficient
There may be the case It will vary substantially depl;fldlng on an ambient enVIronment "()..F5BAl" 01)10 5:~nch IS sa.0I'I 1hB cybncler wllh )he SJamJ ess s.teeJ screws above when 8BA1: Fot DA5. AS, FS. J51ype shIPped When only an auto sWitch 1 $ shipped independenUy.
Combination Symbol: K2 Combination Symbol: K7 An N.C. solenoid valve is used as the supply valve. Also, an external 2 port valve (vacuum valve) must be provided to serve as the vacuum release valve. An air operated N.O. valve is used as the supply valve. An N.C. solenoid valve is used for the vacuum release valve.
Depending on the external switch output type, wire the switch to the communication connector for contact input / output (which is included as an accessory) as shown below. Mount the ferrite core (3 turns), which is included as an accessory. This is an example of wiringRefer to the Communications Operation Manual for more details.
Specifications and performance are the same as those of standard models.
Protective class class # (Mark: ) 120 JSY3000 Series Specify the valve manifold and mounted valve part numbers as well as the ejector manifold and mounted ejector part numbers for ordering. Refer to page 120 for an order example.
Depending on the external switch output type, wire the switch to the connector for contact input / output (which is included as an accessory) as shown below. Mount the ferrite core (3 turns), which is included as an accessory. This is an example of wiringRefer to the Communications Operation Manual for more details.
An amplifying circuit and a dividing circuit are required to produce output which can be read by the counter, and these are accommodated in the case on the cylinder. The sensor head and amplifier section together are referred to as the sensor unit.
Be sure to connect the load to the rod end with the cylinder in an unlocked condition. If this is done when in a locked condition, it may cause damage to the lock mechanism. 1. Do not perform unlocking when an external force such as a load or spring force is being applied. This is very dangerous because the cylinder will move suddenly. Take the following steps. CL CL1 2.
Depending on the external switch output type, wire the switch to the connector for contact input / output (which is included as an accessory) as shown below. Mount the ferrite core (3 turns), which is included as an accessory. This is an example of wiringRefer to the Communications Operation Manual for more details.
Depending on the external switch output type, wire the switch to the connector for contact input / output (which is included as an accessory) as shown below. Mount the ferrite core (3 turns), which is included as an accessory. This is an example of wiringRefer to the Communications Operation Manual for more details.
Trouble shooting 9.1 Alarm and Warning POINT Turn the servo-ON (SON) OFF and shut off the main circuit power supply as soon as the alarm occurs. An alarm or warning is displayed when an abnormality occurs during operation. When an alarm or warning occurs, take appropriate measures according to "LECSN-T Operation Manual, Chapter 8. When an alarm occurs, the ALM is turned off.
Same as standard type Warning Operating Precautions Be aware that smoking cigarettes, etc. after your hands have come into contact with the grease used in this cylinder can create a gas that is hazardous to humans. 46 Series NCQ8 The number of surfaces and grooves where an auto switch can be mounted (as direct mounting).