SMC Corporation of America
Elite Part Number Search
Search Results "HRS200-AN-46-AKS"

Use caution, because an external action such as an impacting load, strong vibration or turning force, may damage the locking mechanism or reduce its life. 20Data Stop signal Amount of overrun 6-12-29 Series C95N Specific Product Precautions 2 Be sure to read before handing. Adjustment Pneumatic Circuit Mounting Warning Warning Warning 2. Do not apply an offset load to the piston rod.

Take appropriate measures to avoid freezing of drain, moisture etc. by use of an air dryer. Not suitable for use as an emergency shutoff valve The valve represented in this catalog is not intended for use as an emergency shutoff valve.

ZS-46-B Panel mount adapter ZS-46-D Panel mount adapter + Front protection cover ZS-46-5L Power supply/output connection lead wire 5-core, 2 m ZS-27-01 Front protection cover B Panel mount adapter Connection Example ZS-46-B PFG300 Sensor connector D Panel mount adapter + Front protection cover PF3A7 H Power supply/output connection lead wire ZS-46-D Lead wire and M12 connector (Option for

Note) The high pressure switch can also be in operation for IDFB55E-46 and IDFB75E-46.

Note 4) F, P, T and S kits are provided with an exhaust on one side, while C kits are with an exhaust on both sides. The number of max. stations differs from kit to kit. (Refer to the table below.)

When the conduit type is used as equivalent to an IP65 enclosure, install a wiring conduit, etc. 9. When an impact, such as water hammer, etc., caused by the rapid pressure fluctuation is applied, the solenoid valve may be damaged. Give an attention to it. 3. Corrosive gas Cannot be used since it will lead to cracks by stress corrosion or result in other incidents. 4.

The Volume Flow of 9.44 l/min applies to an element (Valve, fining, tub etc.) with an equivalent orifice "S" of 1 mm'. lf an lement has for example an "S' ot 4,5 mm', the flow would be 4.5 times higher, in this case 4.5 . 54.44 limin = 245 Umln Example 2: Given an element wilh an 'S'ol 12 mm", a working pressure of 7 bar and an air consumption ot 600 ymin.

The Volume Flow of 9.44 l/min applies to an element (Valve, fining, tub etc.) with an equivalent orifice "S" of 1 mm'. lf an lement has for example an "S' ot 4,5 mm', the flow would be 4.5 times higher, in this case 4.5 . 54.44 limin = 245 Umln Example 2: Given an element wilh an 'S'ol 12 mm", a working pressure of 7 bar and an air consumption ot 600 ymin.

Power supply cable (LEC-CK1-1) is an accessory.

There is no mounting interchangeability with serise CA2. 6-6-46

Do not apply strong impact or an excessive moment while mounting the product or a workpiece. LEC SS-T LEC Y LEC Y If an external force over the allowable moment is applied, it may cause play in the guide or an increase in the sliding resistance. 3.

Note) Please contact SMC when using an individual EXH spacer assembly, an individual SUP spacer assembly, an adapter plate assembly, or an interface regulator on 41P and 43P types.

Note) Since the electrical entry is LO, select an appropriate connector assembly part no.

Retainer prevents an accidental loss of needle.

Mixed single and double wiring is available as an option.

Never use in an atmosphere of explosive gases. The structure of auto switches is not intended to prevent explosion. Never use in an atmosphere with an explosive gas since this may cause a serious explosion. 2. Do not use in an area where a magnetic field is generated. Auto switches will malfunction or magnets inside cylinders will become demagnetized.

7 Made to order common specifications 5.4-46 -XC11 Dual stroke cylinder/Single rod !8 5.4-52 -XC12 Tandem cylinder !

Do not use an air cylinder as an airhydro cylinder. If it uses turbine oil in place of fluids for cylinder, it may result in oil leakage. 5. Combine the rod end section, so that a rod boot might not be twisted. If a rod boot is installed with being twisted when installing a cylinder, it will cause a rod boot to fail during operation.

46 43 27 48 46 46 Shock absorber at retraction end A Shock absorber at extension end MXF Maximum 35 MXW Shock absorber at retraction end MXJ MXP Other dimensions are the same as the basic style.