Table of Contents L4 L4 L5 A L5 D3 D3 T T D2 L1 D2 L1 L2 L2 AS ASP Metric Size ASN A M1 L5 Max.
A port 10 Example) SQ1131-51-C6-A (N.O. specifications) 4 (A) port plug Example) SQ1131-51-C6-B (N.C. specifications) O-ring 2 (B) port plug B port Example) SQ1131-51-C6-B-M (B port plug with manifold block) Direct EXH outlet, built-in silencer [-S] This is a type with an exhaust port atop the manifold end plate. The built-in silencer exhibits an excellent noise suppression effect.
Never use in an atmosphere of explosive gases. The structure of auto switches is not intended to prevent explosion. Never use in an atmosphere with an explosive gas since this may cause a serious explosion. 2. Do not use in an area where a magnetic field is generated. Auto switches will malfunction or magnets inside cylinders will become demagnetized.
In such a case, it will be necessary to use ZSP1 that can detect a small hysteresis or a flow switch. Note) A vacuum generator with a large suction capacity will not be detected properly, so an ejector with an appropriate capacity must be selected. Since the hysteresis is small, vacuum pressure must be stabilized.
In such a case, it will be necessary to use ZSP1 that can detect a small hysteresis or a flow switch. Note) A vacuum generator with a large suction capacity will not be detected properly, so an ejector with an appropriate capacity must be selected. Since the hysteresis is small, vacuum pressure must be stabilized.
In such a case, it will be necessary to use ZSP1 that can detect a small hysteresis or a flow switch. Note) A vacuum generator with a large suction capacity will not be detected properly, so an ejector with an appropriate capacity must be selected. Since the hysteresis is small, vacuum pressure must be stabilized.
Through the concurrent use of a CC series air-hydro unit, it is possible to operate at a constant or low speeds or to effect an intermediate stop, just like a hydraulic unit, while using pneumatic equipment such as a valve.
The rotation range under the adjustment of an angle at 60 is indicated below. The rotation range under the adjustment of an angle at 60 is indicated below. e g n a r n o e ti g a n t a o r R n io R Note) If it is pressurized by the port indicated with the arrow, the shaft rotates in the clockwise direction.
15 28 54.5 54.5 MXH 24.5 80 24.5 MXU (mm) MXS Stroke adjustment range A dimension (Retracted side mounting) Extension end Model Retraction end MXQ Stroke 100 to 150 MXS25-10 MXS25-20 MXS25-30 MXS25-40 MXS25-50 MXS25-75 MXS25-100 MXS25-125 MXS25-150 5 15 25 35 30 15 35 35 35 26 36 46 46 43 27 48 46 46 Shock absorber at retraction end A Shock absorber at extension end MXF Maximum 35 MXW Shock
A change of the input signal will cause an instantaneous movement of the piston rod. easy and simple adjustment of neutral point and operation band from outside.
15 54.5 24.5 80 24.5 (mm) Stroke adjustable range Retracting 5 15 25 35 30 15 35 35 35 A dimension (Retracted side mounting) Extending Model Shock absorber at retraction end MXS25-10 MXS25-20 MXS25-30 MXS25-40 MXS25-50 MXS25-75 MXS25-100 MXS25-125 MXS25-150 26 36 46 46 43 27 48 46 46 Stroke 100 to 150 A Shock absorber at extension end Max. 35 Shock absorber at retraction end Dimensions not
Outside of clean room Duct piping Series 11-/13-/22(Vacuum suction type) With a vacuum pump When several air cylinders are used together or a model with high vacuum suction flow is used. With an ejector When a few air cylinders are locally used.
A magnetic sensor is used in the encoder. Therefore, if the actuator motor is used in an environment where strong magnetic fields are present, malfunction or failure may occur. Do not expose the actuator motor to magnetic fields with a magnetic flux density of 13 mT or more. When installing an electric actuator and an air cylinder with an auto switch (ex.
(A contact) N.O. (A contact) Specifications N.O. (A contact) N.O.
Intermediate stopping of load with an external stopper, etc. When stopping a load in mid-stroke using an external stopper (adjusting bolt, etc.), operate within the operating pressure limits shown in the table below. Use caution, as operation at a pressure exceeding these limits can result in breaking of the magnetic coupling.
Extension locking F Retraction locking B CLJ2 CLM2 1 CLG1 Drop prevention Emergency stop CL1 A MLGC 2 B A CNG B MNB CNA A A CNS 3 B B CLS CLQ A RLQ A 4 B MLU B MLGP ML1C Mounting Caution 1. Be sure to connect the load to the rod end with the cylinder in an unlocked condition. If this is done in the locked state, it may cause damage to the lock mechanism. 2.
Install an air dryer, aftercooler, etc. Excessive condensate in a compressed air system may cause valves and other pneumatic equipment to malfunction. Installation of an air dryer, after cooler etc. is recommended. 3. Drain flushing If condensate in the drain bowl is not emptied on a regular basis, the bowl will over flow and allow the condensate to enter the compressed air lines.
How to Order Type 46 (5 Port/Base mounted) Applicable solenoid valve SYJ340SYJ343SS5YJ3 46 05 M5 Type 46 Type S46 ( ) Single solenoid coil is on same side as the A, B port. M5 x 0.8 R1 R2 port Applicable blanking plate assembly SYJ3000-21-2A Stations Valve mounting direction 02 2 stations Single solenoid coil is on opposite side as the A, B port.
Fire or an explosion can result. This product is not designed to be explosion proof. If using the product in an interlocking circuit: Provide a double interlocking system, for example a mechanical system. Check the product regularly for proper operation. Otherwise malfunction can result, causing an accident.
If a bypass piping set has already been installed and there is a valve, close the valve according to the situation to increase the discharge pressure of the circulating fluid.
③ Check whether the pump operates and the discharge pressure rises to determine if the flow rate is low or not present at all.