110.0 to 110.0 kPa2 MPaPressure sensor: Stainless steel 630, Fitting: Stainless steel 304Fluids do not corrode stainless steel 630 and 304R1/4, NPT1/4, G1/4?, URJ1/4, TSJ1/4, Rc1/8Piping direction: Rear/Bottom12 to 24 VDC ?
110.0 to 110.0 kPa2 MPaPressure sensor: Stainless steel 630, Fitting: Stainless steel 304Fluids do not corrode stainless steel 630 and 304R1/4, NPT1/4, G1/4?, URJ1/4, TSJ1/4, Rc1/8Piping direction: Rear/Bottom12 to 24 VDC ?
0.105 to 1.100 MPa4 MPaPressure sensor: Stainless steel 630, Fitting: Stainless steel 304Fluids do not corrode stainless steel 630 and 304R1/4, NPT1/4, G1/4?, URJ1/4, TSJ1/4, Rc1/8Piping direction: Rear/Bottom12 to 24 VDC ?
111.0 kPa500 kPaPressure sensor: Stainless steel 630, Fitting: Stainless steel 304Fluids do not corrode stainless steel 630 and 304R1/4, NPT1/4, G1/4?, URJ1/4, TSJ1/4, Rc1/8Piping direction: Rear/Bottom12 to 24 VDC ?
111.0 kPa500 kPaPressure sensor: Stainless steel 630, Fitting: Stainless steel 304Fluids do not corrode stainless steel 630 and 304R1/4, NPT1/4, G1/4?, URJ1/4, TSJ1/4, Rc1/8Piping direction: Rear/Bottom12 to 24 VDC ?
110.0 to 110.0 kPa2 MPaPressure sensor: Stainless steel 630, Fitting: Stainless steel 304Fluids do not corrode stainless steel 630 and 304R1/4, NPT1/4, G1/4?, URJ1/4, TSJ1/4, Rc1/8Piping direction: Rear/Bottom12 to 24 VDC ?
Tie-rod Type Low Pressure Hydraulic Cylinder Double Acting/Single Rod Series CHA ø 40, ø 50, ø 63, ø 80, ø 100, ø 125, ø 160 clevis type Double clevis type Center trunnion type Front trunnion type 40 50 63 80 100 40mm 50mm 63mm 80mm 100mm Nil J K Nil N R H Without rod boot Nylon tarpaulin Neoprene cloth Both sides Without cushion With front cushion With rear cushion Aluminum tube Rod boot Part nos. for cylinders with built-in magnets Cushion In the case of cylinders with built-in magnets but no auto switches, do
Do not use two cylinders facing one another horizontally or vertically in such a way that their piston rods strike each other. 8. When the cylinder head side contains hydraulic fluid or is in a normally pressurized condition, the applied load must not be allowed to strike the piston rod end.
Do not use two cylinders facing one another horizontally or vertically in such a way that their piston rods strike each other. 9. When the cylinder head contains fluid or is in a normally pressurized condition, the load should not be allowed to strike the piston rod end. Avoid such applications.
For rail mounting type auto switches, do not remove the rails that are mounted. Since the mounting screw penetrates into the cylinder, the removal of the rails will cause air leakage. Axial direction Perpendicular to axis Auto Switch Mounting Bracket Part Nos. (Band Mounting Type) Mounting Bracket Part Nos. Operation Warning Auto switch mounting bracket part no.
Do not add the suffix (N) indicating no lead wire to the part numbers of models D-A3A, A44A. G39A and K39A. Lead wire length 0.5 m Nil (Example) C73C 3 m L (Example) C73CL 5 m Z (Example) C73CZ None N (Example) C73CN In addition to the models in the above table, there are some other auto switches that are applicable.
Do not connect the white wire of the sensor to c of the display unit.
Rack-and-Pinion Type/Sizes: 10, 15, 20, 30, 40 Series CRQ2 Piping can be installed from one end Body can be used as a flange Compact design saves mounting space Uses internal cushioning 10, 15 : Rubber bumper 20, 30, 40: Air cushion 10: 17mm 15: 20mm 20: 29mm 30: 33mm 40: 37mm 2 auto switches can be mounted on same side (both sides) Angle adjustment bolts are standard Miniature auto switches do
(between lead wire and case) Ambient temperature 10 to 60C Enclosure IEC529 standard IP67, JISC0920: Watertight construction Contact Protection Box/CD-P11, CD-P12 Lead Wire Length D-A9 and D-A9V do not have built-in contact protection circuits. a The operating load is an induction load. b The length of wiring to the load is 5 m or more. c The load voltage is 100 VAC.
Parenlneses CPA1 BN do Boot with Boot' BORE D E G'GB J K M MM N P H z.
To determine whether or not the cylinder can be operated, do not allow the sum (n) of the load factors (n ) for each mass and moment to exceed "1". n = Load mass (m) Max. load mass (m max) + Static moment (M) Allowable static moment (M max) + Dynamic moment (Me) Allowable dynamic moment (Me max) 1 Moment Load mass Max. load mass (Static moment/Dynamic moment) Allowable moment (kg) m M3 m
Basic weight Size 22.5 Single vane 162 90 1 Positioning pin hole 25 161 180 261.5 90 Adjustment bolt (A) Adjustment bolt (B) 3 30 259.5 180 For 90 rotation Single vane (S): 80 to 100 adjustable 440 90 7 50 436 180 675 90 20 Adjustment bolt (A) adjustment range Adjustment bolt (B) adjustment range 60 670.5 180 180 Allowable Loads Do not permit the load and moment applied to the table to exceed
Main switch circuit OUT Black [White] OUT Black [White] DC () Blue [Black] DC () Blue [Black] Indicator light D-Y7BW(V) D-Y59B, Y69B ON OUT (+) Brown [Red] OUT (+) Brown [Red] Operating range OFF Red Indication Green Red Optimum operating position OUT () Blue [Black] OUT () Blue [Black] Contact Protection Boxes/CD-P1 1, CD-P12
(Do not use machine oil or spindle oil ) When bottom mounting, the guide shaft will protrude from the bottom surface Therefore' drill a hole lor a hexagon-holed bolt for mounting and an escape hole for guide shaft on the mounting surface.
Mounting types Cylinder option Bore size B L F T U Basic type Axial foot type Front flange type Center trunnion type Front trunnion type Nil N R H Both sides Without cushion With front cushion With rear cushion 40 50 63 80 100 40mm 50mm 63mm 80mm 100mm Aluminum tube Cushion Part nos. for cylinders with built-in magnets In the case of cylinders with built-in magnets but no auto switches, do