E-ITV-STD-RF-A O ver range of i nput si gnal Pl ease execut e "i ni t i al i ze ( ref er t o P16) " w hen I TV do not operat e norm al l y af t er rest art i ng t he pow er suppl y. Readi ng or w ri t i ng errors occurred i n EEPRO M . Pl ease cont act us, w hen I TV do not operat e norm al l y af t er i ni t i al i ze.
Contact Protection Boxes/CD-P11, CD-P12 Auto Switch Internal Circuits Reed switches
Free mount Speed controllers do not protrude from the top of the body. Top mount Bottom mount Side mount Wiring and piping direction can be selected depending on mounting conditions.
They do not guarantee an actual fixed range (expect approximately 30% dispersion).
There may be large variations depending on the surrounding environment (variations as much as 30%). 12 Compact Cylinder Series CQ2 Auto Switch Mounting Contact Protection Boxes/CD-P11, CD-P12 Auto Switches/Proper Mounting Position for Stroke End Detection D-Z7 and D-Z8 type switches do not have internal contact protection circuits.
(between lead wire and case) Withstand voltage Ambient temperature 10 to 60C Enclosure IEC529 standard IP67, JISC0920 watertight construction Contact Protection Boxes/CD-P11, CD-P12 Lead Wire Length
NCf,IW NCDMW 'Noie: lf ordered do rubber bumper, orcrall length docreases .25 inches. o svE' Stainless Steel Cylinder Air Cylinder Series NCM Specifications 250 PSt(17.5 kgf/cm') 8 PSI (0.5 kgf/cm'?)
I installed \tl .1 onry) f e lri=d.c-) L Type of actuation With irdicator ght and surge v0rrage suppress0r 1 INormal closed 2 lNormal open S and Z not available lor grornmel. i 1 oVAC type inc udes S (do not specity). Body Port size ut subplate _,,' (a --1ry1 wv : Standard typerindividual gilot exhaust l--l l ?
(lf lubrication is used, do not discontinue its us.) Olf the kinetic energy oI the load exceeds the permissible range, use external stops to absorb load. O Connect piping atter thoroughly flushing it. O Do not use trydraulic fluid. @Shaft Load lf a static (i.e. non-dynamic) load only is applied to the actuatot it is possible io apply the load values shown in the table below.
Do not allow repeated bending or stretching forces to be applied to lead wires. Wiring arrangements in which repeated bending stress or stretching force is applied to the lead wires can cause broken wires. 1. Do not drop or bump. Do not drop, bump or apply excessive impact (1,000m/s) when handling.
Do not apply a load that involves shocks such as those caused by pounding (particularly with the ball bushing style). 4. If this mass is applied, the deflection of the guide shaft will also have a large value.
Do not hold the terminal block box or the switch. ISE70 ZSE80 ISE80 Lead wire with connector ZSE ISE Knurl ZSP PS 3. Connect the colored wires coming from the cable terminal. Refer to the circuit diagram and table above to avoid mistakes.
Do not scratch or gouge the sliding portion of the piston rod. Damaged seals etc. will result in leakage or malfunction. 4. Do not dent or scratch the mounting surface of the body and the plate. The flatness of the mounting surface may not be maintained, which would cause an increase in sliding resistance. 5.
Do not service or attempt to remove product and machinery/ equipment until safety is confirmed. 1. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.
" 0.006 8.3 Note 2) Rotating torque under pressure 0.5 MPa Note 3) Do not use the fittings with a leak tester or for vacuum retention because they are not guaranteed for zero leakage.
Gripping fingers do not scrape the tube during insertion or removal. 2. Body SMCs composite body offers: 1. Weight savings 2. Compact dimensions 3. High performance 4. Superior chemical resistance 2. Lower insertion and release forces. 7.
As the connected actuator will start operating due to this manual operation, be sure to confirm that it is safe to do so beforehand. Ex. 1) Cable length: 300 mm DXT1215T-5W1U-01m(-X1) Symbol for electrical entry MNon-locking push type Push the manual override button all the way down. 2.
Do not use a lubricator on the inlet side of the product, as the bleed mechanism can malfunction. Caution 1. For emergency action in the event of setting failure or leakage from the relief port, refer to Troubleshooting in the Operation Manual of the product. Piping Warning Air Preparation Equipment 1.
Do not use a lubricator on the inlet side of the product, as the bleed mechanism can malfunction. Caution IRV 1. For emergency action in the event of setting failure or leakage from the relief port, refer to Troubleshooting in the Operation Manual of the product. VEX SRH Piping Warning SRP SRF 1.
Do not use a lubricator on the inlet side of the product, as the bleed mechanism can malfunction. Caution IR 1. For emergency action in the event of setting failure or leakage from the relief port, refer to Troubleshooting in the Operation Manual of the product. IRV VEX Piping Warning SRH SRP 1.