m3/sN02NPT1/4118 g90 gC01Rc1/8114 g86 g1 x 10?5 Pa?m3/s
rep-filter-e See Fig. 4] For FN112-10, two screws are mounted in the middle of the guide assembly [M3 See Fig. 4] 2-6. The element can now be pulled out of the cover. Do not disassemble the element any further. Note) Reassembly should be performed by reversing the disassembly procedure. Refer to the schematic drawings for the assembly and disassembly procedures for the cover, seals etc.
Moment (Nm) Payload (N) ML1C/M2,M3 How to calculate the load ratio A. Consider q Max. payload, w static moment, e dynamic moment (when stopper collides) when calculating the Max. allowable moment and payload. Evaluate q and w as a (average speed), and e as (collision speed =1.4a).
.: 04 (ø4), Thread: R, Port Size: M3 (M3 x 0.5)
.: 23 (ø3.2, use ø1/8" Tubing), Thread: R, Port Size: M3 (M3 x 0.5)
.: 04 (ø4), Thread: R, Port Size: M3 (M3 x 0.5)
.: 23 (ø3.2, use ø1/8" Tubing), Thread: R, Port Size: M3 (M3 x 0.5)
m (95% filtered particle size)Max. 0.1 mg/m3 (ANR) (Before saturated with oil: 0.01 mg/m3 (ANR) or less, approx. 0.008 ppm) (2)PolycarbonateOption80.18
m (95% filtered particle size)Max. 0.1 mg/m3 (ANR) (Before saturated with oil: 0.01 mg/m3 (ANR) or less, approx. 0.008 ppm) (2)PolycarbonateStandard250.22
m (95% filtered particle size)Max. 0.1 mg/m3 (ANR) (Before saturated with oil: 0.01 mg/m3 (ANR) or less, approx. 0.008 ppm) (2)PolycarbonateStandard250.22
m (95% filtered particle size)Max. 0.1 mg/m3 (ANR) (Before saturated with oil: 0.01 mg/m3 (ANR) or less, approx. 0.008 ppm) (2)PolycarbonateStandard250.22
m (95% filtered particle size)Max. 0.1 mg/m3 (ANR) (Before saturated with oil: 0.01 mg/m3 (ANR) or less, approx. 0.008 ppm) (2)PolycarbonateOption80.18
m (95% filtered particle size)Max. 0.1 mg/m3 (ANR) (Before saturated with oil: 0.01 mg/m3 (ANR) or less, approx. 0.008 ppm) (2)PolycarbonateStandard450.44
Note Lead wire length: 2m With mounting screws (M3 x 5L: 2 pcs.)
(reference value) M3: Yawing Selection Flow Chart Operating conditions Reexamine operating conditions m: Load mass (kg) V : Speed (mm/s) P : Operating pressure (MPa) Mounting Orientation: Accuracy: Tentative selection of cylinder model MY1B : Basic MY1M : Slide bearing MY1C : Cam follower guide MY1H : High precision guide MY1HT: High rigidity/high precision guide Select a guide suitable for
(Not a\ailabl on NCRBI BWl0) x ( ) : When porl A is pressunzed. x x Optional M3 fiiing available S ho/r lo ofder page NCDRBIOWIQoI$ol[r$Q Rotation Time Setting Bodg To k Used As A Flange ltcRElB\ltfto Actual Torque Even a small torque generated by the rotary actuator, due to inertia, can cause damage. Therefore.
View A PFW31(-M) PFW3-B DIN rail type 8-M3 3 x 7.2 (= 21.6) 36 2-3.4 6.4 15 1 2 3 4 6.5 26 FLOW SWITCH SMC 35.5 30 56 (4.5) 44 UNIT RESET SET 5 6 7 8 29 38 15.2 26
with each other either horizontally or vertically Plug connection ower supply output connection 30 e-Con connector Analog output or auto shift input 2 outputs + Sensor connection M5 female thread, through type (with mounting holes) M3 M5 female thread, through type M5 6 reducer 4 reducer R1/8,NPT1/8 Applications Manifolding is possible.
price of compressed air: 3 yen/m3 (ANR) Pressure: 0.5 MPa Operation time of the compressor: 2,500 h/year To reduce pressure loss: 1 Regulate at the proper pressure. 2 Reduce the restriction and pressure loss on the fittings. 3 Improve the effective sectional area ratio of the nozzle to the inlet side by adopting a nozzle with a small diameter.
A side: Orange (for supply valve) B side: Green (for release valve) Release flow adjustment needle (With light/surge voltage suppressor) 33.3 4.4 Pressure setting trimmer Pilot valve exhaust port Hysteresis setting trimmer (M3: Port PE) Silencer (AN203-KM8) 57.1 62.1 47.5 39.7 29.5 21 33.6 23.5 10 Vacuum port (5.25) (13.5) 3.75 (8.25) 6 One-touch fitting Port V Supply port 16.75 88 19 Button