Conforming to ISO Standard Solenoid Valve (with M12 Connector) Series EVS7-6/7-8/7-10 (Size 1) (Size 2) (Size 3) 1 Note 2) Impact resistance: No malfunction resulted during an impact test using a drop impact tester. The test was performed one time each in the axial and right angle directions of the main valve and armature for both energized and de-energized conditions. Vibration resistance: No malfunction resulted during an one-sweep test between 8.3 and 2000 Hz.
Piston speed mm/s Piston speed mm/s Piston speed mm/s Features 6
/M AI N TEN AN CE At t ach t o t he m ai n pi pi ng t o rem ove cont am i nant s of oi l , w at er, f orei gn m at eri al i n com pressed ai r. Fi l t rat i on rat i ng3 m ( Fi l t rat i on ef f i ci ency99% ) Fl ui d ot her t han com pressed ai r Ai r pressure m ore t han 1. 0 M Pa** and 0. 05M Pa* or l ess Fol l ow i ng envi ronm ent s l ead to cause breakage.
Dynamic viscosity [m2/s] Viscosity [Pas] Density [kg/m3] Formulas below can be used for common units 1cP = 1mPas = 10-3Pas 1cSt = 1mm2/s = 10-6m2/s 13 Working Principle 1. When air is supplied, it passes through the switching valve and enters drive chamber B. 2.
Dynamic viscosity [m2/s] Viscosity [Pas] Density [kg/m3] Formulas below can be used for common units 1cP = 1mPas = 10-3Pas 1cSt = 1mm2/s = 10-6m2/s Pulsation Attenuating Capacity The process pump generates pulsation because it discharges a liquid using two diaphragms.
An application which could have negative effects on people, property, or animals requiring special safety analysis. 4.
When selecting an exhaust cleaner, refer to the selection method shown below, as the selection method will differ for exhaust from actuator drive systems, etc., and exhaust from ejectors, etc.
Install an air filter near this product on the supply side. Select a filtration degree of 5m or less. 2. Compressed air containing a large amount of drainage can cause malfunction of this product and other pneumatic equipment. As a countermeasure, install an after-cooler, air dryer or water separator, etc. 3.
When selecting an exhaust cleaner, refer to the selection method shown below, as the selection method will differ for exhaust from actuator drive systems, etc., and exhaust from ejectors, etc.
Cylinder speed should be in the range of 50 mm/s to 300 mm/s. In addition, prevent knocking and bounding. Do not give torque to the piston rod. Is torque given to the piston rod?
ZSE50F / ISE50 1 x 10 -5Pam3/s ZSE60F / ISE60 1 x 10 -10Pam3/s IP65 Enclosure Panel mount With bracket Option Panel mount + Front side protection cover To confirm working pressure of hydraulic cylinder Application examples To confirm adsorption of work pieces containing water To confirm primary pressure of cleaning line Features 1 High precision and high resolution 1/2000 (0.1kPa) Positive
U nderst and t hi s operat i on m anual w i l l be revi sed w i t hout not i f i cat i on. To get t he best perf orm ance f rom your purchase, be sure t o read t hi s m anual caref ul l y bef ore use. M I CRO M I ST SEPARATO R Seri es AM D W ARN I N G Chem i cal s Corrosi ve gas + At m osphere Cont ai ni ng organi c sol vent *N .
O . auto drai n: M i n. 0. 1 M Pa O PERATI O N M AN U AL M i n. 0. 05 M Pa M ax. 1. 0 M Pa Keep f ol l ow i ng t o operat e M i st separat or properl y. Fol l ow i ng envi ronm ent s l ead t o cause breakage. Envi ronm ent Low er t han 5 D o not use under f ol l ow i ng envi ronm ent . D o not use under f ol l ow i ng condi t i ons.
U nderst and t hi s operat i on m anual w i l l be revi sed w i t hout not i f i cat i on. To get t he best perf orm ance f rom your purchase, be sure t o read t hi s m anual caref ul l y bef ore use. W ARN I N G Chem i cal s Corrosi ve gas + At m osphere Cont ai ni ng organi c sol vent *N . C. aut o drai n: M i n. 0. 15 M Pa *N .
auto switch) 236 IN 165 118 71 20 10 XB7 Cold-resistant cylinder (40 to 70 C) (without an auto switch) 314 OUT 220 157 94 XB9 Low speed cylinder (10 to 50 mm/s) 378 IN 264 189 113 XB10 Intermediate stroke (Using exclusive body) 25 12 491 OUT 344 245 147 XB13 Low speed cylinder (5 to 50 mm/s) XC6 Piston rod, retaining ring, rod end nut made of stainless steel Manufacture of Intermediate Stroke
SRF 1 07 11 0 S S 1 With nut Body size 1 3 5 Fitting type Pilot port thread type Made to Order (Refer to page 887 for details.)
When removing the connector, unlock the knurled part and pull out the connector straight. 0o [ oU2] Output mode of OUT2 2 [ HYS] Hysteresis mode If using the product in an interlocking circuit: Provide a double interlocking system, for example a mechanical system Check the product regularly for proper operation Otherwise malfunction can result, causing an accident. [ 2ot] Switch operation
This pressure switch does not have an explosion proof rating. Never use in the presence of an explosive gas as this may cause a serious explosion. 3. Do not use in an environment where static electricity can cause problems, otherwise system failure or malfunction may result.
Note 2) Impact resistance: No malfunction resulted during an impact test using a drop impact tester. The test was performed one time each in the axial and right angle directions of the main valve and armature for both energized and deenergized conditions. Vibration resistance: No malfunction resulted during an one-sweep test between 8.3 and 2000Hz.