o I installed \tl .1 onry) f e lri=d.c-) L Type of actuation With irdicator ght and surge v0rrage suppress0r 1 INormal closed 2 lNormal open S and Z not available lor grornmel. i 1 oVAC type inc udes S (do not specity). Body Port size : Standard typerindividual gilot exhaust ut subplate _,,' (a --1ry1 wv l--l l ?
Note 2) Do not release the OUT side piping port of the product directly to the atmosphere without connecting piping. If the product is used with the piping port released to atmosphere, accuracy may vary.
Do not use a screwdriver with a large grip or with a tip that does not fit into the trimmer groove because this could strip the groove.
voltage suppressor VZ 4(A)/2(B) port size Type of actuation VF Manual override Electrical entry Rated voltage Thread type Body option VFR Option 1 0 5 01 L Body ported VZ5 2 VP4 VZS Type of actuation Option VFS 2 position single solenoid F: With foot bracket (2 position single type only) Body option VS4 1 0: Individual exhaust for the pilot valve VQ7 2 position double solenoid EVS Note) Do
Do not disassemble the product or remove parts as it could cause breakdown of the product. 2. Flow rate is controlled by balancing the valve body. Do not expose the product to external vibration and impact as it changes the flow rate. Vibration may occur depending on the piping conditions or control methods.
Nil: Without bracket F1: With foot bracket A, B port size 3 10-SY3000 5 10-SY5000 Thread piping 2 position single only Coil type Symbol Port size M5 x 0.8 10-SY3000 Applicable series 7 9 10-SY7000 10-SY9000 M5 Standard Nil 1 8 01 10-SY5000 T With power saving circuit (24, 12 VDC only) Actuation type 1 4 10-SY7000 02 02 03 2 position single 1 4 Power saving circuit is not available for D, DO
Do not install by directly grasping the cylinder tube, as this could cause a tube to deform and malfunction. 2. Do not install it by directly grasping the piston rod with a pair of electricians pliers. Scratches on the piston rod would cause a bearing or rod seal to get damaged, malfunction, and leak air. 10 12.4 4 15 12.8 20 13.2 16
Do not use this aftercooler in an area that has viscous dust (electrostatic paint powder, oily particles, etc.). If it must be used under such conditions due to unavoidable circumstances, please contact SMC beforehand.
Option Port size (P, A, B port) Thread type Nil F G Rc Nil Z None Nil 01 Without sub-plate 1 8 1 4 With light/surge voltage suppressor 02 N NPT Piping (P, A, B, EA, EB port) T NPTF EA, EB port: Rc 1/8 Nil B Side ported Bottom ported Option SJ 1 00 01 F Plug-in VFR2 5 SY 1 E 10 1 Non plug-in VFR2 02 SV CE-compliant SYJ Q CE-compliant Nil Pilot valve manual override SZ Electrical entry: D/DO
Note 1) Do not use the product in an atmosphere and place where there is direct contact with chemicals. It may cause damage to the body. (Alcohol, acetone, etc. also cause damage, so be sure for the product not to be close to them.) Note 2) Do not use it in a line that is kept pressurized because it could cause the body to break.
Do not repair the fittings or patch the tube for reuse. 25 Series KFG2 Specific Product Precautions 2 Be sure to read before handling. Refer to back cover for Safety Instructions, Handling Precautions for SMC Products (M-E03-3) for Fittings and Tubing Precautions.
(Fig. 1) Also, do not use the cylinder with fixed at external slider to avoid excessive moment applied to bearing of the cylinder.
With 2 auto switches Same surface Different surfaces 6 A A-6 15 Auto switch model REA REB Auto Switch D-M9 D-M9W 6 B B-6 REC The auto switch is mounted by slightly displacing it in a direction (cylinder tube circumferential exterior) so that the auto switch and lead wire do not interfere with each other.
Otherwise, chattering will occur. conditions to calculate the product life, and do not exceed it. The maximum access limit of the memory device is 1 million cycles.
Lube Cast iron Chromated (In the case of aluminum alloy casted) Aluminum alloy casted (Iron tube: Cast iron) Non-lube Piston Chromated (In the case of aluminum alloy casted) Aluminum alloy casted (Iron tube: Cast iron) Air-hydro Caution Mass/Aluminum Tube: Lube (Non-lube, Air-hydro) Do not open the cushion valve excessively.
Do not scratch or gouge the sliding portion of the piston rod and the guide rod. Damaged seals, etc. will result in leakage or malfunction. 4. Do not dent or scratch the mounting surface of a body and a plate. The flatness of the mounting surface may not be maintained, which would cause an increase in sliding resistance.
Caution Do not uninstall, with the power supply connected to the controller.
Caution Do not uninstall, with the power supply connected to the controller. The driver will not be uninstalled correctly. -6No.SFOD-OMT0008 Revision history No.
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed.
Do not install, copy or use this Software if the terms of this Agreement cannot be accepted. The terms of this Agreement must be accepted by the user before downloading this Software if this Software has been supplied by SMC via the Internet or any other means. Do not download this Software if you cannot accept the terms of this Agreement. Article 1 (Grant of license) 1.