Do not use in an environment where they are exposed to or come in contact with organic solvents, chemicals, cutting oil, synthetic oil, ester-based compressor oil, alkali, and thread lock solutions. 2. Avoid applications where pressurized air is frequently introduced to and released from the standard bowl of an air filter, filter regulator, or lubricator.
Hex. across flats may be deformed, if using an improper wrench for hex. across flats.
Then with one side fixed, gradually close the other side and measure 2R at the point where the tubing folds or flattens, etc. 2R Fixed side How to Order Burst pressure drop curve 1.00 Length TL0604 TIL01 20 20 Symbol 20 50 100 2S Type Length 20 m 50 m 100 m 2 m Metric sizes Burst pressure drop coefficient 0.80 Roll Inch sizes 0.60 Straight Please refer to the series chart and specifications
If the power should not come back on, please contact SMC for an inspection.
Install an air filter at the upstream side of valve. Select an air filter with a filtration degree of 5m or finer. 3. Install an aftercooler, air dryer or drain catch before the filter and take appropriate measures. Compressed air that contains excessive foreign material may cause malfunction of valves and other pneumatic equipment.
An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. This product is not designed to be explosion proof.
Do not use the product in an environment where corrosive gases or fluids could be splashed. Otherwise damage to the product and malfunction can result. Do not use in an area where surges are generated.
10, 16, 20, 25: 40 mm, Bore size 32, 40: 80 mm.
(8.3-2O0OHz) o External Pilot Tape,/ NVJ300R An external pilot supply is required when main valve pressures are lower than 20 PSl.
(8.3-2O0OHz) o External Pilot Tape,/ NVJ300R An external pilot supply is required when main valve pressures are lower than 20 PSl.
(8.3-2O0OHz) o External Pilot Tape,/ NVJ300R An external pilot supply is required when main valve pressures are lower than 20 PSl.
20 2-M6 thread depth 11 2-M6 thread depth 11 15 15 35 18 15 2-M6 thread depth 11 2-M6 thread depth 11 20 20 A 17 17 40 A 20 20 15 45 60 25 45 60 A Applicable clamp cylinder A Applicable clamp cylinder Part no.
Otherwise, injury or an accident may occur. 20 - 5. Do not put hands, etc. in between the air gripper fingers or attachments. Otherwise, injury or an accident may occur. 6. When removing the air gripper, first confirm that no workpieces are being held and then release the compressed air before removing the air gripper.
C a u t i o n ~ Install an air filter. Install an air filter upstream near the valve. Select an air filter with a filtration size of 5m or smaller. ~ Take appropriate measures to ensure air quality, such as providing an aftercooler, air dryer, or water separator. Compressed air that contains a large amount of moisture can cause the malfunction of pneumatic equipment such as valves.
(Roll moment) Moment MXW25 120 70 (Static moment/Dynamic moment) Allowable Moment MXW25 70 100 50 (Nm) 30 40 Maximum moment (Nm) Maximum moment (Nm) 50 MXW20 25 30 40 Roll moment Pitch moment Yaw moment MXW20 20 Model Mr Mp/Mep My/Mey 15 MXW16 20 MXW16 12 10 15 3 5 5 MXW8 7 10 MXW12 MXW12 2 10 10 MXW12 4 5 7 5 4 3 12 20 20 MXW16 MXW8 MXW8 3 2.5 25 40 40 MXW20 2 2 1.5 50 100 200 300 500 65
Install an air dryer, aftercooler, etc. Excessive condensate in a compressed air system may cause valves and other pneumatic equipment to malfunction. Installation of an air dryer, after cooler etc. is recommended. 3. Drain flushing If condensate in the drain bowl is not emptied on a regular basis, the bowl will over flow and allow the condensate to enter the compressed air lines.
AXT100-20-2-05 AXT100-20-2-06 AXT100-20-2-01 AXT100-20-2-02 AXT100-20-2-03 AXT100-20-2-04 Valve Mounting VS After confirming the gasket is correctly placed under the valve, tighten the mounting screws with the appropriate torque listed below.
Note 5) The system accuracy when combined with an applicable flow sensor.
This is included in the response from the product when there is an error in the received request. 9 NAK(15h) Error content is included in the response when there is an error in the received request. Refer to the table below for exception codes.