Thermo-chiller Series HRS Compact Type (Except HRS050) Cooling capacity Note 4) (50/60 Hz) (W) Temperature stability Note 6) (C) Pump capacity Note 7) (50/60 Hz) (MPa) Rated flow Note 8) (50/60 Hz) (L/min) Tank capacity (L) Port size 5 to 40 1100/1300 1500/1700 0.1 0.13/0.18 (at 7 L/min) 7/7 Approx. 5 Rc1/2 Stainless steel, Copper (Heat exchanger brazing), Bronze, Alumina ceramic, Carbon, Polypropylene, PE, POM, FKM, EPDM, PVC Wetted parts material
BMP1-032 70C J Nylon tarpaulin 110C K Heat resistant tarpaulin Maximum ambient temperature for the rod boot itself. 6-7-5
Implement suitable protective measures in locations where there is contact with water droplets, oil, or welding spatter. 7. Install a silencer into exhaust port to prevent the dust ingress if there is a lot of dust in atmosphere, as dust may cause air leakage. Maintenance Warning 1.
(mm) 4 5 6.5 8 W: White, R: Red, BU: Blue, Y: Yellow, G: Green, C: Clear, YR: Orange, (All tubes are the same color regardless of 2 cores or 3 cores.) 2 3 4 5 No. of cores 2. Reel (50 m, 100 m length, Color changes) Suffix -X3 to the end of part number. Ex.) TFU0425B-2-50X3 6 7 3. No. of cores (10 m roll, each color) 8 Suffix -X4 to the end of part number. Ex.)
Accessory C is available only with Rc thread.
Suspension equipment and lifting devices also require measures to prevent dropping. 7) Consider the possibility of power source related malfunctions.
Output data Offset MSB LSB MSB LSB (Word) 15 8 7 0 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 -38No.EX-OMP0013-E Dimensions If a fieldwireable connector is used for the power supply connection, and the SI unit is installed directly to a valve manifold, the cable connectors outer diameter should be 16 mm or less.
7 !8 @1 @6 14A !9 @0 CJ1 CJP @7 i o CJ2 80, 100 CM2 C85 !0 !1 CG1 @2@3@4@5 14B MB Locking at rod end C95 CA1 CS1 Manual release non-locking style: L Material Note Component Parts Material Note Component Parts No. q w e r t y No. !7 !8 !
Connection thread size Proper tightening torque (Nm) M R 1/8 7 to 9 R 1/4 12 to 14 H/DL L/LL R 3/8 22 to 24 R 1/2 28 to 30 KC Installation of Threads 3. Tightening tools Tighten with an appropriate wrench using the hexagon wrench flats on the body. Position the wrench on the base as close as possible to the threads.
7 !8 !9 @0 @1 @2 Material Aluminum alloy Aluminum alloy Aluminum alloy Carbon steel Note Clear hard anodized Clear hard anodized Chromated No.
Class B or equivalent (130C) Note) Coil insulation type Note) Based on JIS C 4003 How to Order 1 L 02 0 1 1 4 VS C Thread type Direct operated/Metal seal solenoid valve Electrical entry Nil Rc NPT NPTF Option 4, 5 port valve N Symbol Electrical entry Electrical entry position C T U D T Sub-plate Conduit Type of actuation Conduit with terminal Sub-plate Body size: 1/8 standard F Single
ZS-28-C 1 pc. Connector for PSE300 PF2 Specifications IF Conforms to CE marking and UL (CSA) standards.
(No freezing) Ambient temperature 0 to 60 C (No freezing) Maximum viscosity 5000 mPas Recommended operating cycle 1 to 7 Hz (0.2 to 1 Hz also possible depending on conditions)Note 2) Pilot air solenoid valve recommended Cv factor Note3) 0.45 Weight 3.0 kg Mounting orientation Horizontal (with mounting foot at bottom) Packaging General environment Note1) With cycles at 2 Hz or more.
Precoutions on Selection 7 7. Precautions on Design 7 8. Mounting Methods 8 9. Piping 11 10. Operating Environment 12 11. Speed Control 12 12. Clean Series / Precautions 13 13. Troubleshooting 17 14. Auto Switch 18 1 Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage.
To remove and install the snap ring for the knuckle pin or the trunnion pin, use an appropriate pair of pliers (tool for installing a type C snap ring for hole).
ZS-10-5 A-50 1 pc. 0.6 m 30 3 m 50 5 m Specifications Model ZSP1-B ZSP1-S Fluid Air Operating pressure range 20 to 101 kPa Applicable adsorption nozzle dia. 0.3 to 0.7 (Refer to Graph (1) on page 16-7-3.) 0.5 to 1.2 (Refer to Graph (2) on page 16-7-3.)
LT C edition Safety Instructions Be sure to read Precautions for Handling Pneumatic Devices (M-03-E3A) before using.
ON ON A (/) 1 OFF OFF DC(+)DC(-) 2 ON DC(+)DC(-) NPN PNP () 3 OFF ( ) () DC(+) DC(-) () 4 () 5 -47NO.ZK2-OM00801-B No. 80 mA (Er1,2) () ( (Er1,2) ) (Er0,4,6,7,8,9) DC24 DC24 V10% (Er0 4 6 7 8 V10% 9) 6 "HHH" (HHH) "LLL" (Er3) (LLL) (Er3) 3.5 F.S. DC24 V10% DC24 V10% DC(+) DC(-) 7 -48NO.ZK2-OM00801-B No.
Specifications .7 3-3. Gripping force .8 3-4. Dimensions .10 3-5. Connector and pin layout . 11 3-6. Center of gravity . 11 4.Product Specifications .13 4-1. Magnet gripper .13 4-2. 3-port solenoid valve .14 4-3. Auto switch .15 5.Operating method or operation .16 5-1Precautions for Design .16 5-2. Installation .17 5-3. U R C a p .20 5-4. Air supply .26 5-5. Piping .26 5-6.