CJ5-S Do not immerse the cylinder in water or chemicals. When the cylinder is operated in a condition with water pressure, the fluid leaks into the cylinder in the early stages. In the worst case, the fluid may back flow inside the piping and damage the solenoid valve. Maintenance Warning Mounting 1.
Do not disassemble the power clamp No special maintenance is necessary because the power clamp has a fully enclosed design to protect the clamp against welding spatter, and also the power clamp has a contamination resistant construction. Do not disassemble any parts other than replaceable parts, otherwise it may reduce the performance of the clamp cylinder. 3.
Also, do not attempt to tighten the bumper bolt without using a nut. If the dumper bolt is removed, the piston hits the head cover causing damage to the cylinder. Therefore, do not use a cylinder without a bumper bolt. Furthermore, if the bumper bolt is tightened without a nut, the piston seal is caught in the leveled part, damaging the seal. 3.
Note 1) Do not use the product in an atmosphere and place where there is direct contact with chemicals. It may cause damage to the body. (Alcohol, acetone, etc. also cause damage, so be sure for the product not to be close to them.) Note 2) Do not use it in a line that is kept pressurized because it could cause the body to break.
Do not use compressed air that contains chemicals, organic solvents, salt, or corrosive gases. Do not use compressed gas containing chemicals, organic solvents, salt or corrosive gas. This can cause rust, damage to rubber and resin parts, or malfunction. Liquid surface of drain Discharge drainage until the drainage level reaches the center. 3.
PAuto switch attachment Auto switches can be selected that do not protrude from cylinder body. P2 roller materials available to suit application requirements.
For the auto switch mounting rail, do not remove the pre-equipped rail. Since the mounting thread is drilled through inside a the cylinder, it will result in air leakage. MVGQ For basic style, the port position in a head cover is available either perpendicular to the axis or in-line with the cylinder axis.
Do not immerse the cylinder in water or chemicals. When the cylinder is operated in a condition with water pressure, the fluid leaks into the cylinder in the early stages. In the worst case, the fluid may back flow inside the piping and damage the solenoid valve. Maintenance Warning Mounting 1.
Also, do not attempt to tighten the bumper bolt without using a nut. If the dumper bolt is removed, the piston hits the head cover causing damage to the cylinder. Therefore, do not use a cylinder without a bumper bolt. Furthermore, if the bumper bolt is tightened without a nut, the piston seal is caught in the leveled part, damaging the seal. 3.
Do not scratch or gouge the sliding portion of the piston rod and the guide rod. Damaged seals, etc. will result in leakage or malfunction. 2.
Do not put hands or fingers between the plate and body. Care should be taken that hands or fingers do not get caught in the space between the cylinder body and the plate when air pressure is applied. 1. Do not scratch or dent the sliding parts of the piston rod and guide rods. Damage to seals may cause air leaks or faulty operation. 2.
Do not move the cover upward inadvertently during end plate installation.
VQ valves are ideal for applications requiring high speed, frequent operation, stable response time and long service life. Innovative mounting methods allow valves to be changed without entirely disassembling the manifold. Built-in one-touch fittings save piping time and labor., "MFLD, VQ, 4/5 PORT SOLENOID VALVE
Stations: 8 Stations, Lead Wire: Top Wire Entry, Cable Length: 5.0m Cable, Option: DIN Rail Mount w/o DIN Rail
Stations: 5 Stations, Lead Wire: Side Wire Entry, Cable Length: 5.0m Cable, Option: DIN Rail Mount w/o DIN Rail
Stations: 10 Stations, Lead Wire: Top Wire Entry, Cable Length: 1.5m Cable, Option: DIN Rail Mount w/o DIN Rail
Stations: 12 Stations, Lead Wire: Top Wire Entry, Cable Length: 3.0m Cable, Option: DIN Rail Mount w/o DIN Rail
Stations: 4 Stations, Lead Wire: Top Wire Entry, Cable Length: 5.0m Cable, Option: DIN Rail Mount w/o DIN Rail
Stations: 5 Stations, Lead Wire: Top Wire Entry, Cable Length: 3.0m Cable, Option: DIN Rail Mount w/o DIN Rail
Stations: 6 Stations, Lead Wire: Side Wire Entry, Cable Length: 5.0m Cable, Option: DIN Rail Mount w/o DIN Rail