Connect End Plate and tighten removed screws by specified tightening torque. (0.6 Nm) Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. Note 1. The power supply should be off while setting the switches. 2.
Red flashing SI unit has detected the transmission rate, but is not addressed by the DP master OFF Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. This product is not designed to be explosion proof.
Do not connect the terminating resistor outside, when the setting switch for the terminating resistor is ON. (4)How to connect.
;(E a Slip exceeding retaining force may damage brake shoe, which could lead to reduced relaining force, resulting in its shorter lile a Cylinder loading should be within 35'/" of holding force when the brake is used for droo oroteclion, a Do not apply any impact when you load the cylinder in the locked position.
Do not mark or damage lhe piston rod. This could cause damage to packing and resull in lluid 'eakage. O Do not apply oil lo the sliding section of lhe piston rod, O Do nol apply rclary torque. O Do not apply large-load energy to the model wilh a shock absober when ths shock absolbet is absorbrng enrgy twhen the levt is uprighl).
Do not exceed the tightening torque of 3.5 Nm when installing piping. Exceeding this value may cause malfunctioning of the sensor. 4. The minimum bending radius of the cable is 50 mm. 5. Do not use pressure sensors with corrosive and/or inflammable gases or liquids. 1. Incorrect wiring can damage the switch and cause a malfunction or erroneous switch output.
Normal Bottom Peak BATTERY 1.5V x 2 LR6 G kV MADE IN JAPAN IZD IZE POWER LIGHT 110 Do not apply a strong impact on the sensing part.
Do not apply a load to a cylinder which is greater than the allowable value stated in the Model Selection. Applying an improper load may cause malfunctions. 3. Do not use the cylinder in an environment where the cylinder is expose to moisture, adhesive foreign matter, dust or liquid such as water or cutting fluid.
Do not operate with the magnetic coupling out of position. If the magnetic coupling is out of position, push the external slider by hand (or the position slider with air pressure) back to the proper position at the stroke end. 3. Do not apply a lateral load to the external slider.
Do not inadvertently move the guide adjusting unit. The guide is installed at the proper tightening torque. Do not loosen the mounting bolts of the guide. 2. Do not operate the magnetic rodless cylinder if the magnet couplings on the actuator are displaced.
Do not service or attempt to remove product and machinery/ equipment until safety is confirmed. 1. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.
Do not use fluid containing solid matter. This will cause faulty operation. IR IRV VEX SRH SRP SRF SRF ITV IC ITVH ITVX PVQ VY1 VBA VBAT AP100 891
Do not use in an environment where vibration or impact occurs. Please contact SMC about use under such conditions because it can cause fracture or malfunction.
DO Without Air Cushion B Bore size (mm) Part no.
Do not allow hands or fingers near the cylinder during its operation. Your fingers may be caught between the body and the plate. If you need to come near the cylinder during its operation, install a cover on the cylinder. 4. Do not bring objects that are sensitive to magnetism near the cylinder. There is a magnetic built into the cylinder.
DO MY Bore size (mm) 22 22 30 30 45 45 60 CY DX DS DH Z DDH10 DC DT DU DR DO DL DE B DA DB Model 20 25 32 40 50 63 80 14 14 20 20 30 30 32 7 7 8 8 10 10 14 44 44 60 60 86 86 110 15 15 18 18 22 22 24 10 10 11.5 11.5 14 14 15 6.6 6.6 9 9 11 11 13.5 9 9 10.5 10.5 12.5 12.5 13 62 62 81 81 111 111 136 42 42 53 53 73 73 90 32 32 43 43 64 64 78 39 43 49 59 71 82 106 +0.058 0 +0.058 0 129 151 185
When raising the unit, do not insert your hands or fingers. As this is a heavyweight product, be sure to use caution. Screw holes for installing eyebolts are provided for 180, 200 and 250. (Eyebolts are not included in the unit.) Tie-rod nut, Spring washer Cylinder Tie-rod -X Wing nut Unit holding tie-rod 3.
Do not inadvertently move the guide adjusting unit. The guide is installed at the proper tightening torque. Do not loosen the mounting bolts of the guide. 2. Do not operate the magnetic rodless cylinder if the magnet couplings on the actuator are displaced.
Do not operate with the magnetic coupling out of position. If the magnetic coupling is out of position, push the external slider by hand (or the piston slider with air pressure) back to the proper position at the stroke end.