180 Angular Style Air Gripper Series MHY2/MHW2 Cam Style Rack & Pinion Style 1 M5 x 0.8 (Finger opening port) D3 O 20S 13 3 23 7 M5 x 0.8 (Finger closing port) 4 2 MHY2-10D2 Opening/Closing direction through-hole type 4-3.4 (Hole for mounting attachment) 6 0.005 0.025 3 6 12 (Limted area for mounting attachment) Do not extend the attachment from limited area for mounting to avoid interference with the attachment or main body. 12-10-11 11 Series MHY2 Dimensions MHY2
Do not use in locations having an explosive atmosphere. 2. Do not operate in locations where vibration or impact occurs. 3. In locations near heat sources, block off radiated heat. 1. Operate within the range of the maximum operating pressure. Caution 1. After a long period of non-use, perform inspections before beginning operation. 2.
When mounting the load with screws, do not exceed the maximum tightening torque. (The torque may vary depending on the material of the load.) Bolt Model Maximum tightening torque (Nm) Caution MGJ6 M2.5 x 0.45 0.5 MGJ10 M3 x 0.5 1.0 1. Do not scratch or dent the sliding parts of the piston rod and guide rods. Damage to seals can cause air leakage or malfunction, etc. 2.
Mounting from upper side l l Model Bolt Maximum tightening torque (Nm) l (mm) MGF 40 MGF 63 MGF100 M6 x 1 10 7.5 M8 x 1.25 25 9 M10 x 1.5 51 9 Mounting from bottom side Do not bring objects that are sensitive to magnetism near the cylinder. There is a magnetic built into the cylinder. Do not bring magnetic disks, cards, or tapes near the cylinder. Data may be lost.
Standard Stroke Do not use the product as a stopper. Do not disassemble and modify the product.
Do not scratch or gouge the escapement by dropping or bumping it when mounting. Even a slight deformation can cause inaccuracy or malfunction. 2. Please observe the specified torque limits when tightening screws to mount the attachment.
Although switches satisfy the IEC standard IP67 structure (JIS C0920: anti-immersion structure) (except D-A3l, A44l, G39l, K39l), do not use switches in applications where they are continually exposed to water splash or spray.
Do not exceed the screw-in torque of 3.5 Nm when installing piping. Exceeding this value may cause malfunctioning of the sensor. 4. The minimum bending radius of the cable is 50 mm. 5. Do not use pressure sensors with corrosive and/or inflammable gases or liquids. 1. Incorrect wiring can damage the switch and cause a malfunction or erroneous switch output.
;(E a Slip exceeding retaining force may damage brake shoe, which could lead to reduced relaining force, resulting in its shorter lile a Cylinder loading should be within 35'/" of holding force when the brake is used for droo oroteclion, a Do not apply any impact when you load the cylinder in the locked position.
Do not mark or damage lhe piston rod. This could cause damage to packing and resull in lluid 'eakage. O Do not apply oil lo the sliding section of lhe piston rod, O Do nol apply rclary torque. O Do not apply large-load energy to the model wilh a shock absober when ths shock absolbet is absorbrng enrgy twhen the levt is uprighl).
Do not use in locations having an explosive atmosphere. 2. When vibration or impact is applied, make sure to test in the 2.
Do not supply lubrication, as this is a non-lube product. The interior of the cylinder is lubricated at the factory, and lubrication with turbine oil, etc., will not satisfy the product's specifications. 6. Never reapply lubricant. Never reapply lubricant, as there may be a degradation of particulate generation or operation characteristics. 2.
For AC specifications, NIL is only set for Electrical entry DO. IN IN Note) Bracket cannot be attached later.
For AC specifications, Nil is only set for electrical entry DO. Right Left Right Left IN IN Options (For details, refer to page 12.)
Caution Do not disconnect the USB cable during Teaching. If disconnected, the actuator will stop suddenly and the servo will be turned OFF.
Caution Do not disconnect the USB cable during Teaching. If disconnected, the actuator will stop suddenly and the servo will be turned OFF.
Do not load the Card Motor with continuous or higher thrust than allowed for a prolonged time. When a pushing operation step data is selected, the pushing force is continuously generated from [Operation Start] until [Operation End (Stop)] is pressed.
Please avoid excessive overwriting. (4) Do not cut the power while data is being saved.
Do not service or attempt to remove pr confirmed. 3. Do not service or attempt to remove pr confirmed. 3. Do not service or attempt to remove pr 3. Do not service or attempt to remove pr 3.
Do not service or attempt to remove confirmed. 3. Do not service or attempt to remove confirmed. 3. Do not service or attempt to remove 3. Do not service or attempt to remove 3.