SI unit for AS-Interface Fault No.11 Problem Possible cause Investigation method Countermeasures The inputs that are beyond the maximum point number do not operate. Check that the number of inputs has not exceeded the allowable number. The allowable number depends on the SI unit model. Inadequate total number of inputs from the Input block connected with the SI unit.
Description and Functions 9 5-1 LED indication 9 5-2 Terminal board 9 5-3 Address setting 10 5-4 Setting of Hold/Clear 11 6. Wiring 12 6-1 Communication wiring 12 6-2 Terminal resistance 13 6-3 Cable for communication line 13 6-4 Wiring to power supply 13 7. Troubleshooting 14 -1No.EX-OMF0012-B 1.
If the minimum setting unit is 1 L/min, the flow can be displayed in 1 L/min units, i.e. 10, 11, 12. Minimum setting unit N Normal condition (NOR) Reference condition for volumetric flow: 101.3 kPa, 0 C The flow measurement which is converted at normal atmospheric pressure conditions at 0 C.
Exhaust Port Exhaust Residual pressure exhaust button (2.9) Port -4- Warning Warning Design/ Selection Design/ Selection (11) Push the residual pressure exhaust button all the way to the end position by using a tool. Push the residual pressure exhaust button all the way to the end position by using a tool having a tip diameter of 2.8 or below.
No.PS-OMM0005-J PRODUCT NAME Digital Pressure Switch MODEL / Series / Product Number ZSE10(F) ISE10 Table of Contents Safety Instructions 2 Model Indication and How to order 9 Summary of Product parts 11 Definition and terminology 12 Mounting and Installation 15 Installation 15 Piping 17 Wiring 18 Internal circuit and wiring example 19 Pressure Setting 20 Measurement mode 20 Function Setting
Recommended tightening torque: Modular AR/AW series 0.60.05 Nm ARM10/11 series 0.320.03 Nm Mount the main body of the Pressure switch. Insert the lock pin to the adapter to the end firmly. Supply pressure slowly, and ensure no air leaks.
No.PS-OMM0003-J PRODUCT NAME Digital Pressure Switch MODEL / Series / Product Number ZSE80(F) ISE80(H) Table of Contents Safety Instructions 2 Model Indication and How to Order 9 Summary of Product parts 10 Definition and terminology 11 Mounting and Installation 14 Installation 14 Piping 16 Wiring 17 Pressure Setting 19 Measurement mode 19 Function Setting 21 Function selection mode 21 Default
Air Cylinder Speed controller Solenoid valve Regulator Air source Air filter Fig. 11 Basic Circuit 28 6.
Order for tightening mounting screws 11 2-9-2. Auto switches When an auto switch is mounted or its set position is changed, refer to Fig. 4 to 11. C a u t i o n Use a specific mounting bracket (Page 19, Table 2) . Tighten mounting screws to the appropriate torque. The auto switch can only be used for cylinders with a built-in magnet for auto switch (e.g. CDA).
13 90 3.2 AR60K-B 70 66 65.8 11 13 90 3.2 Note 1) B dimension is a size in the state to unlock the handle.
AW20-B 11 AW20-B 0.80.1Nm AW30-B 17 AW30-B 2.350.3Nm AW40-B 21 AW40-B 3.50.3Nm Disassembly Remove the bowl assembly, housing, and element. Hexagon Remove a housing from a body by turning 4 mounting screws to the left with a hexagon wrench key. wrench key Nominal5 Remove the valve guide.
Operation and Mounting 2.1 Air Supply -P. 5 2.2 Operating Environment -P. 6 2.3 Design -P. 6 2.4 Mounting and Installation -P. 8 2.5 Piping -P. 10 2.6 Speed Control -P. 11 2.7 Shock Absorbing Mechanism -P. 11 2.8 Directional Control -P. 12 2.9 Mounting of Auto Switch -P. 13 3. Maintenance and Inspection 3.1 Inspection -P. 14 3.2 Maintenance -P. 14 3.3 Replacement Parts -P. 14 4.
Refer to Disassembly Drawing on page 11 for the part No. and the replacement procedure of the finger assembly and the body assembly. 15 - Construction/Parts list 2 MHF2-12D to 20D Components No. Description Material Note No.
Wiring 1) Insert cable gland (4), washer (5) and rubber seal (6) into cable (7) in order, and insert it into housing (2). 2) Loosen screws (11) on terminal (3). Insert lead wires (10) and tighten screws (11) again. Note 1) The tightening torque should be 0.5 Nm +/15%. Note 2) The applicable outside diameter of cable (7) is 6 to 8 mm.
Check if the dispersion is within the display accuracy range. 11 Product failure Replace the product. -52No.PS-OML0003-J Fault No. Fault Possible cause Investigation method Countermeasure Install a 5 m filter to prevent foreign matter from entering the pressure port. Also, clean the filter regularly to prevent drainage deposits.
Not adhering to these specifications, can result in damage to the product. 11 XL*-OMI0013-B 7-2.
Warranty period and guaranteed range 10 6.Parts replacement procedure 11 1 XM-OMP0001-A Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
9 P3313128 P3313228 MHR3-10 MHR3-15 Description Cover Main parts MA D533 MHR3/MDHR3 Series Nominal Size 10 Without auto switch: MHR3-10R 3 x M3 x 0.5 thread depth 6 P.C.D.24 (Mounting thread) 120 120 25 25 M3 x 0.5 Finger opening port M3 x 0.5 Finger closing port 44 29 9h9 0 0.036 33.5 1 5 4 16 (36.5) 12 2 2 3e8 0.014 0.028 Open: 11 Closed: 8 8 0 0.05 4 3 x M3 x 0.5 thread depth 6 (Thread
Description Material Note No. 1 2 3 4 5 6 7 8 9 Description Material Note 20, 25: Resin Body Aluminum alloy Hard anodized MHY 10 Cap 32 to 50: Aluminum alloy Piston Hard anodized Aluminum alloy Hard anodized 11 12 13 14 15 16 17 Piston bolt Stainless steel Pinion gear Carbon steel Heat treated MHW MHW Ball bearing Carbon steel Seal cover Schield type Brass Key Carbon steel Bumper Urethane