FSQ seies Do not mark or damage lhe piston rod. This could cause damage to packing and resull in lluid 'eakage. O Do not apply oil lo the sliding section of lhe piston rod, O Do nol apply rclary torque. O Do not apply large-load energy to the model wilh a shock absober when ths shock absolbet is absorbrng enrgy twhen the levt is uprighl).
. * Options are shipped together with the product but do not come assembled. 9 2-Color Display Digital Flow Switch RoHS PF2M7-L Series How to Order Integrated display Made to order (Refer to page 26.)
Do not use in locations having an explosive atmosphere. 2. When vibration or impact is applied, make sure to test in the 2.
For AC specifications, NIL is only set for Electrical entry DO. IN IN Note) Bracket cannot be attached later.
For AC specifications, Nil is only set for electrical entry DO. Right Left Right Left IN IN Options (For details, refer to page 12.)
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. 1. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.
Caution Do not disconnect the USB cable during Teaching. If disconnected, the actuator will stop suddenly and the servo will be turned OFF.
Caution Do not disconnect the USB cable during Teaching. If disconnected, the actuator will stop suddenly and the servo will be turned OFF.
Do not load the Card Motor with continuous or higher thrust than allowed for a prolonged time. When a pushing operation step data is selected, the pushing force is continuously generated from [Operation Start] until [Operation End (Stop)] is pressed.
Please avoid excessive overwriting. (4) Do not cut the power while data is being saved.
Use under conditions where pressure fluctuations (pulsations) exceeding 0.1 MPa do not occur. Operating pressure MAX. 0.99MPa Vacuum 1.310-6kPa Operating temperature 5oC to 80oC Element proof differential pressure MAX. 0.1MPa Element reverse differential pressure MAX. 0.05MPa Not possible to use with connecting in reverse.
Use under conditions where pressure fluctuations (pulsations) exceeding 0.1 MPa do not occur. Operating pressure MAX. 0.99MPa Vacuum 1.310-6kPa Operating temperature 5oC to 80oC SFB10MAX. 0.5MPa Element proof differential pressure SFB20-02 MAX. 1.0MPa SFB10MAX. 0.07MPa Not possible to use with connecting in reverse.
Connection 1) Rc connection Confirm that chips from the pipe threads and sealing material do not enter the piping. Also, when sealant tape is used, leave 1.5 to 2 thread ridges exposed at the end of the threads. -4- Piping Piping 2) TSJ connection The TSJ fitting is a kind of a self-align fittings.
Operating Environment Warning (1) Do not operate under the conditions listed below due to a risk of malfunction. In locations having corrosive gases, organic solvents, and chemical solutions, or in locations in which these elements are likely to adhere to the equipment. In locations in which salt water, water, or water vapor could come in contact with the equipment.
Do not service or attempt to remove pr confirmed. 3. Do not service or attempt to remove pr confirmed. 3. Do not service or attempt to remove pr 3. Do not service or attempt to remove pr 3.
Do not service or attempt to remove confirmed. 3. Do not service or attempt to remove confirmed. 3. Do not service or attempt to remove 3. Do not service or attempt to remove 3.
Connect End Plate and tighten removed screws by specified tightening torque. (0.6 Nm) Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. Note 1. The power supply should be off while setting the switches. 2.
Red flashing SI unit has detected the transmission rate, but is not addressed by the DP master OFF Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. This product is not designed to be explosion proof.
Do not connect the terminating resistor outside, when the setting switch for the terminating resistor is ON. (4)How to connect.