LCD Readout Digital Pressure Switch Series ZSE3 (For Vacuum)/ISE3 (For Positive Pressure) For General Pneumatics Easy pressure setting with the digital display Can be integrated with a vacuum unit, Series ZX ZSE ISE ZSP PS ISA PSE IS ISG ZSM Built-in fail IS ISG ZSM 769 Series ZSE3/ISE3 Dimensions/Switch Only Grommet type 30 SE3I Z 01 T1 20.5 RESET button DOWN button SET button UP button Lead wire length 600 3.5 (3000) 40.5 8.5 01: R 1/8 T1: NPTF 1/8 2 x 3.5 Mounting hole 13 M5 x 0.8 Connector type 30 SE3C I Z 01 T1 20.5 RESET button DOWN button SET button UP button Lead wire length 600 3.5 (3000) 10 39 8.5 01: R 1/8 T1: NPTF 1/8 2 x 3.5 Mounting
JIS D 1601 as standard 30 G, 3 times at X, Y, Z IP50 (IEC standard) 5 m, 10 m, 15 m, 20 m Cable: 7; 6 core twisted pair shielded wire; oil, heat and frame resistant cable Extension cable (Option) Note) Digital error under Controller (CEU2), Counter (CEU5) is included.
Operating direction: Right Operating direction: Left a b c d e f g Nil Reed switch L R Solid state switch S h Nil L R S Operating direction Left Right a b h g d c f e Note) Lead wire length symbols 0.5m .
D Auto identification function Display units can be selected using either or . This function automatically identifies the pressure range of the pressure sensor that is connected to the multi-channel pressure sensor controller, thus eliminating the need of having to reset the range again after replacing the sensor.
N.O. 1 (P) 3 (R) 1 (P) 3 (R) a c e d a c e d (A) (A) 2 2 g g 3 (R) 1 (P) 3 (R) 1 (P) b b f f Component parts Replacement parts Note Zinc die-casted No.
Connector Connector for input or output devices with cable, D-sub connector or spring type terminal block.
Every time the button is pressed, the value will change from A to Z and 0 to 9. When the button is pressed, the value changes in the opposite direction. : If the password does not match, "wrong password" is displayed on the input screen.
You do not need to specify "N" (i.e., without lead wire) for D-A3, D-A44, D-G39, and D-K39. This is the only standard specification automatically available for these models. D-A9V, M9V, M9WV, and M9A(V) models cannot be mounted on 25 to 40. Since there are applicable auto switches other than listed, refer to page 310 for details.
D-X Individual -X 817
Dimensions IN574-95 (Sensor head + Display part) 20 40 230 D-F8N (2 pcs.) 110 Red tape 500 20 M12 Connector Tube (3 places) Green tape Sensor head Wiring Terminal no. Description Note 1 +15 V 1 2 1 2 5 2 Output signal 1 D-F8N 3 4 3 4 Display part 3 GND Socket connector A-coded (Normal key) Plug connector A-coded (Normal key) 4 Output signal 2 D-F8N DD1677
Power saving circuit is only available in the "Z" type.
Operating: 0 to 50C, Stored: 10 to 60C (with no freezing and condensation) Resistance Operating or Stored: 35 to 85%RH (with no condensation) 10 to 500 Hz with a 1.5 mm amplitude or 98 m/s2 acceleration, in each X, Y, Z direction for 2 hrs, whichever is smaller.
Power saving circuit is only available in the "Z" type.
(example: If the Pressure switch with output impedance of 1 k is connected to the A/D converter to detect the analogue output of 5 V, the detected voltage by the A/D converter becomes 5(V) 1(M)/(1(k) + 1(M)) 4.995(V), and there is an error of approximate 0.005 V). Output impedance Output type The operation type of the switch output.
Note 0.03 BJ2-010 Common use to all of D-C7, C8 and D-H7 0.02 BJ2-016 Note) A set of stainless steel mounting screws BBA4 is attached. (A switch mounting band is not attached. Please order the band separately.) BBA4 screws are used for D-C7/C8/H7. D-H7BAL switch is set on the cylinder with the screws above when shipped.
BBA1: D-A5/A6/F5/J5 D-F5BAL switch is set on the cylinder with the screws above when shipped. When a switch only is shipped, BBA1 screw is attached.
Option Bore size (mm) Description 6 Bore size (mm) Bracket 6 Symbol Specifications 10 16 10 16 XA Change of rod end style XB6 Heat resistant cylinder (150C) Auto switch D-A9(V), D-M9(V), D-M9W(V) Flange CP-F006A CP-F010A CP-F016A XB7 Cold resistant cylinder Foot Single knuckle joint CP-L006A CP-L010A CP-L016A I-P006A I-P010A I-P016A XC22 Fluororubber seals Trunnion (with pin) CP-T006A CP-T010A
VDW Option Enter together in order, counting from station 1 on the D side. 20 20 stations None DIN rail mounting DIN rail mounting (Without DIN rail) Nil D DO VQ VX2 U side D side Stations321 VX VX3 VXA A port VN P1 LVC How to Order Valves (For Manifold) LVA VQ M C6 2 1 1 1 G LVH Series/ Orifice size LVD Port size Symbol 2 3 Series VQ20 VQ30 LVQ VQ20 VQ30 Symbol C6 C8 C10 C12 Port size
(For band mounting, only the auto switch mounting brackets are assembled before shipment.) * When mounting a band on bore size 8, 10, or 12, the D-A9l(V) cannot be mounted. * When mounting a rail on bore size 8, 10, or 12, the D-A9l(V) and A79W cannot be mounted. * When mounting a rail on bore size 20 or 25, the D-M9l(V), M9lW(V), and M9lA(V) cannot be mounted. 2 C85 Series Specications Bore
Consult with SMC regarding water resistant types with the above model numbers. 2 1 m type lead wire is only applicable to D-A93. Solid state auto switches marked "" are produced upon receipt of order. Do not indicate lead wire length symbol N (none) for types D-A3, D-A44, D-G-39 or D-K39.