EX250-SDN1(-X102)_eng Connect End Plate and tighten removed screws by specified tightening torque. (0.6 Nm) Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. Note 1. The power supply should be off while setting the switches. 2.
Red flashing SI unit has detected the transmission rate, but is not addressed by the DP master OFF Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. This product is not designed to be explosion proof.
Do not connect the terminating resistor outside, when the setting switch for the terminating resistor is ON. (4)How to connect.
;(E a Slip exceeding retaining force may damage brake shoe, which could lead to reduced relaining force, resulting in its shorter lile a Cylinder loading should be within 35'/" of holding force when the brake is used for droo oroteclion, a Do not apply any impact when you load the cylinder in the locked position.
Do not mark or damage lhe piston rod. This could cause damage to packing and resull in lluid 'eakage. O Do not apply oil lo the sliding section of lhe piston rod, O Do nol apply rclary torque. O Do not apply large-load energy to the model wilh a shock absober when ths shock absolbet is absorbrng enrgy twhen the levt is uprighl).
Do not exceed the tightening torque of 3.5 Nm when installing piping. Exceeding this value may cause malfunctioning of the sensor. 4. The minimum bending radius of the cable is 50 mm. 5. Do not use pressure sensors with corrosive and/or inflammable gases or liquids. 1. Incorrect wiring can damage the switch and cause a malfunction or erroneous switch output.
Do not use in an atmosphere having corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. 2. Do not operate in locations where vibration or impact occurs. 3. In locations which receive direct sunlight, provide a protective cover, etc. 4. In locations near heat sources, block off any radiated heat. 5.
Do not service or attempt to remove product and machinery/ equipment until safety is confirmed. 1. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.
Normal Bottom Peak BATTERY 1.5V x 2 LR6 G kV MADE IN JAPAN IZD IZE POWER LIGHT 110 Do not apply a strong impact on the sensing part.
Do not use the product outdoors. 2. Do not place heavy objects on top of this product, or step on it. The external panel can be deformed and danger can result. Caution 1. Install on a rigid floor which can withstand this products weight. 2. When you remove casters to install the product, lift the product at least 10 mm by using adjuster-foot etc.
Do not apply a load to a cylinder which is greater than the allowable value stated in the Model Selection. Applying an improper load may cause malfunctions. 3. Do not use the cylinder in an environment where the cylinder is expose to moisture, adhesive foreign matter, dust or liquid such as water or cutting fluid.
Do not operate with the magnetic coupling out of position. If the magnetic coupling is out of position, push the external slider by hand (or the position slider with air pressure) back to the proper position at the stroke end. 3. Do not apply a lateral load to the external slider.
Do not apply a load beyond the line on the graph. 4 Series CQU Compact Cylinder: Plate Type Double Acting, Single Rod Construction !4 r w u !2 !0 e o y !3 i q !1 t Rod end male thread Component Parts Note Replacement Parts: Seal Kit Kit no. Material Description No.
Do not inadvertently move the guide adjusting unit. The guide is installed at the proper tightening torque. Do not loosen the mounting bolts of the guide. 2. Do not operate the magnetic rodless cylinder if the magnet couplings on the actuator are displaced.
Do not service or attempt to remove product and machinery/ equipment until safety is confirmed. 1. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. 1. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.
Do not use in an environment where vibration or impact occurs. Please contact SMC about use under such conditions because it can cause fracture or malfunction.
(Do not use spindle oil or machine oil.) MQQ M Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com 3. Use a metal seal type when using solenoid valves for cylinder actuation.
DO Without Air Cushion B Bore size (mm) Part no.