<br>With lever detection switch (For RS2H/RSH series cylinders): The state of the lever is detected separately by the proximity switch to the judge whether a workpiece is present or absent.<br><br>

<br>4) It remains interchangeable with old CA2 series cylinders.<br><br>

<br>For further details on the pivot bracket, refer to “Dimensions of Accessories” in the CM2 series catalog, which can be found here.<br><br>

<br>※A “Z” is suffixed to the end of the refreshed product part number after the stroke (e.g., CJ2D16-30Z).<br><br>Note) The CBJ2 series cylinder with end lock has not been refreshed (as of 2018). Features of the refreshed products are as follows.<br>① A head cover with boss to improve cylinder mounting flexibility has been added.

<br><br>Part number: Rod boot part number-Stroke symbol<br><br>Ex.) The rod boot part number for the CA2B63-1100JZ is “C2A50GAEA034-R-A10.”<br>Note 1) A band for the rod boot is included.

<br>Note 2) The pivot receiving bracket can be used for the clevis type or trunnion type. <br><br>

<br>The 2-wire type has a large leakage current, and there are cases where the switch OFF state cannot be recognized when used in combination with a PLC.<br>The 3-wire type has separate power supply and signal lines, and NPN or PNP output must be selected according to the input specifications. <br><br>Leakage current:<br>3-wire type: 100 μA or less for 24 VDC Ex.)

<br>It is not necessary to loosen the band fixing screw either.<br><br>・To replace the auto switch, insert the D-M9 series auto switch into the auto switch mounting groove of the switch holder.<br>Then, secure the M2.5 set screw supplied with auto switch with a watchmaker's (precision) screwdriver. <br><br>

<br>The CDA2 series catalog can be found here.<br><br>

<br>Keep the hexagon nut and seal washer, as they will also be used with the internal shock absorbers.<br>Precautions:<br>① Make sure it is known that the product specifications have been changed from those indicated by the part number on the product nameplate for maintenance and safety purposes.

<br>Note) In the CRB series catalog, the position (90°) of the start point of the chamfered part represents approximately 90°.<br><br>

<br>① By using the power supply connector EMG terminal (OFF/OFF) <br>② By using RESET (alarm reset and operation interruption) <br>③ By using HOLD (operation pause) <br>Of the 3 methods, ② and ③ are performed with the servo ON. <br>When stop method ① is performed with the servo set to OFF, the servo will be turned OFF automatically.

<br>Therefore, it is necessary to change the basic parameter that determines the movable range when changing the return to origin direction. <br>Refer to the following documents for further details. <br><br><br><br>

<br>(1) U-shaped slide bending test: more than 10,000,000 cycles (Test conditions: bending radius = cable outer diameter ø5.5 x 6 times, slide distance = 300 mm, approx. 40 times/min)<br>(2) 90-degree bending test: more than 10,000,000 cycles (Test conditions: bending radius = cable outer diameter ø5.5 x 6 times, load 0.9 kg, approx. 30 times/min)<br><br>Note 1) The motor cable of approx.

(e.g., when the leakage rate is 20 L/min (ANR), the vacuum pressure of a ZH10□SA is -20 kPa and the vacuum pressure of a ZH10□LA is about -32 kPa, so the L type has a higher vacuum pressure) <br>The ZH series catalog can be found here.<br><br>

<br>The new ZK2□A series vacuum unit was released in June 2019.<br>The pilot valves for the supply valve and release valve have been changed, but the connector, flow rate characteristics, vacuum performance, and mounting dimensions are the same as those of old ZK2 series vacuum units.<br>Pressure switches and manifold DIN rail mounting brackets can be retrofitted.

<br>Note that bleed is a phenomenon associated with the nozzle flapper, which is separate from the relief action (action to depressurize when the set pressure rises too much). <br><br>Note 1) Be sure to use a mist separator in addition to the filters on the inlet side of IR1000/2000/3000 series regulators.

<br><br>

<br>For the IR400-02/03/04□□: IR3000-02/03/04□□-A<br>For the IR401-02/03/04□□: IR3010-02/03/04□□-A<br>For the IR402-02/03/04□□: IR3020-02/03/04□□-A<br>For the IR412-02/03/04□□: IR3120-02/03/04□□ (IR-A series air operated regulators will be available at a later date.) <br>Note) Select option “H” when panel mounting the product.

<br><br><br><br>The air filter as a whole will need to be replaced in such cases.