<br><br>

<br><br>

<br>VV5QC11 gasket part number: VVQ1000-80A-1 (12 pcs./set) <br>VV5QC21 gasket part number: VVQ2000-80A-1 (12 pcs./set) <br>VV5QC41 gasket part number: VVQ4000-80A-1 (10 pcs./set) <br>VV5QC51 gasket part number: VVQ5000-80A-1 (10 pcs./set) <br><br>The above gasket part numbers are also applicable to VQ1000/2000/4000/5000 series plug-in valves.

<br>Check the JIS symbol in the location indicated in the “Dimensions” section of the VM400/800 series catalog to ensure proper piping.<br><br>

<br><br>● The MY series mechanically jointed rodless cylinder: Video<br>For MY series mechanically jointed type cylinders, there is an opening in part of the cylinder pipe that allows for a slide table to be connected to the piston.

<br>With lever detection switch (For RS2H/RSH series cylinders): The state of the lever is detected separately by the proximity switch to the judge whether a workpiece is present or absent.<br><br>

<br>4) It remains interchangeable with old CA2 series cylinders.<br><br>

<br>For further details on the pivot bracket, refer to “Dimensions of Accessories” in the CM2 series catalog, which can be found here.<br><br>

<br>※A “Z” is suffixed to the end of the refreshed product part number after the stroke (e.g., CJ2D16-30Z).<br><br>Note) The CBJ2 series cylinder with end lock has not been refreshed (as of 2018). Features of the refreshed products are as follows.<br>① A head cover with boss to improve cylinder mounting flexibility has been added.

<br><br>Part number: Rod boot part number-Stroke symbol<br><br>Ex.) The rod boot part number for the CA2B63-1100JZ is “C2A50GAEA034-R-A10.”<br>Note 1) A band for the rod boot is included.

<br>Note 2) The pivot receiving bracket can be used for the clevis type or trunnion type. <br><br>

<br>The 2-wire type has a large leakage current, and there are cases where the switch OFF state cannot be recognized when used in combination with a PLC.<br>The 3-wire type has separate power supply and signal lines, and NPN or PNP output must be selected according to the input specifications. <br><br>Leakage current:<br>3-wire type: 100 μA or less for 24 VDC Ex.)

<br>It is not necessary to loosen the band fixing screw either.<br><br>・To replace the auto switch, insert the D-M9 series auto switch into the auto switch mounting groove of the switch holder.<br>Then, secure the M2.5 set screw supplied with auto switch with a watchmaker's (precision) screwdriver. <br><br>

<br>The CDA2 series catalog can be found here.<br><br>

<br>Keep the hexagon nut and seal washer, as they will also be used with the internal shock absorbers.<br>Precautions:<br>① Make sure it is known that the product specifications have been changed from those indicated by the part number on the product nameplate for maintenance and safety purposes.

<br>Note) In the CRB series catalog, the position (90°) of the start point of the chamfered part represents approximately 90°.<br><br>

<br>① By using the power supply connector EMG terminal (OFF/OFF) <br>② By using RESET (alarm reset and operation interruption) <br>③ By using HOLD (operation pause) <br>Of the 3 methods, ② and ③ are performed with the servo ON. <br>When stop method ① is performed with the servo set to OFF, the servo will be turned OFF automatically.

<br>Therefore, it is necessary to change the basic parameter that determines the movable range when changing the return to origin direction. <br>Refer to the following documents for further details. <br><br><br><br>

<br>(1) U-shaped slide bending test: more than 10,000,000 cycles (Test conditions: bending radius = cable outer diameter ø5.5 x 6 times, slide distance = 300 mm, approx. 40 times/min)<br>(2) 90-degree bending test: more than 10,000,000 cycles (Test conditions: bending radius = cable outer diameter ø5.5 x 6 times, load 0.9 kg, approx. 30 times/min)<br><br>Note 1) The motor cable of approx.

(e.g., when the leakage rate is 20 L/min (ANR), the vacuum pressure of a ZH10□SA is -20 kPa and the vacuum pressure of a ZH10□LA is about -32 kPa, so the L type has a higher vacuum pressure) <br>The ZH series catalog can be found here.<br><br>