Silencers/Exhaust Cleaner Series AN /Series AMC 1 Also add the capacity of the piping from the cylinder to the EXH. 2. Select a model that provides a maximum processing flow volume that exceeds the consumption volume obtained in step 1.
5 ~ 60C / 40 ~ 40F Temperature Rc(PT) 1/8, 1/4 Port Size 01: 25mm2 02: 27.5mm2 Effective Area Model Port Size NPT A B C NAK2000-N01, 02 18, 14 50 25 22 NAK4000-N02, 03, 04 14, 38, 12 67 36 36 NAK6000-N06, 10 34, 1 95 50 50 H O W T O O R D E R ( N ) A K 2 0 0 0 S E R I E S 000 (N)AK P O R T S I Z E M O D E L 01 1/8 02 1/4 03 3/8 04 1/2 06 3/4 10 1 P O R T T H R E A D 2 1/4 4 1/2 6 1 Nil Rc
When a fitting is over tightened, more of the sealant material is squeezed out. Remove the squeezed out sealant material. 4. When tightening is not sufficient, it will cause sealing failure or a loose fitting. 5. Re-using 1) Normally, a fitting with sealant can be re-used 2 to 3 times. 2) Remove the sealant material that is separated and adhering to a removed fitting with air blow, etc.
Av o i d m o u n t i n g t h e v a l v e i n a p o s i t i o n w h e re i t w i l l b e s u b j e c t t o vibration. 2. Ensure that pipework is thoroughly clean and free of water and debris during installation. 3. U s e a t h r e e c o r e s c r e e n e d c a b l e f o r s i g n a l a n d p o w e r. C o n d u c t o r diameter minimum 0.5mmeach core 4.
16 No.ZL3-OM00801-A 7.2 1 (/) ZL3/ZL6 ZL3-JSY3140-5LZ -a 1 3) 2) DC24V 1) 300mm 300mm * *0.150.18Nm 2) D: E: 1 1 1 1 3) 1 1 2 X12 ZL3/ZL6 SY100-30-4A-6 1 2) / 1) 2) 300 4 DC24V 6 600 10 1000 15 1500 20 2000 25 2500 30 3000 50 5000 ZL3/ZL6 SY100-30-A *x2 17 No.ZL3-OM00801-A ZL3/ZL6 ZS-39-5G ZL3-LW1-N-A 1 1) N NPN P PNP 2 ZL3/ZL6 ZL3-EJ1-H-A 1 2) 1) M 0.35 MPa
Panel When mounting on a panel, refer to page 561 in Specific Product Precautions. 4.5 M5 x P0.5 8.5 M6 x P0.5 5.5 71 11 18 124 46 53 92 10 10 9.5 Bleed Bleed 63 Exhaust SUP(1) OUT(2) 30 OUT(2) SUP(1) 43 35 2 x Rc 1/8 Port size EXH 43 50 50 2 x Rc 1/4 Port size 2 x Rc 1/8 35 60 2 x Rc 1/8 Pressure gauge port Pressure gauge port 50 Mounting hole IR300-0 IR2120-02 36 2 Bracket (Option) 30
P36201021 7 NBR Damper P36202026 P36202026 2.5 x 1 8 NBR O-ring 2 x 1.25 2 x 1.25 9 NBR O-ring 4.5 x 1 4.5 x 1 4.5 x 1 4.5 x 1 10 x 1.3 10 NBR O-ring 27.8 x 1.5 JISB2401 P11 JISB2401 P11 27.8 x 1.5 11 NBR O-ring JISB2401 P5 Note 2) JISB2401 P5 Note 2) 12 NBR O-ring JISB2401 P16 Note 2) JISB2401 P16 Note 2) 13 NBR Seal (A) P36203015 P36203015 14 NBR Seal (B) P36203016 P36203016
Note 2) Applicable up to 2000 mL/min by using a solenoid valve with a large Cv value (Cv value of 0.5 or more).
(Representative valve) Ambient and operating air temperature -5 to 60 oC (No freezing) C(dm3/(sbar)) 0.6 [1(P) 2(A)] , 0.5 [2(A)3(R)] Flow rate characteristics b 0.2 [1(P) 2(A)] , 0.15 [2(A)3(R)] Port size Rc, NPT, G1/8 ON timing ON upon the set delay Output method Normal close Reset Resets by exhausting the input signal pressure Weight 480g *) The dispersion is shown excluding the first
If a sealant tape is used, leave 1.5 to 2 threads exposed. 2 Wrap this way. Leave 2 threads. Sealant tape Handling Caution (1) Do not apply force when transferring, mounting and dropping the regulator with a pressure gauge.
Conditions and environments outside of the given specifications, or use outdoors or in a place exposed to direct sunlight. 2.
If a sealant tape is used, leave 1.5 to 2 threads exposed. 2 Wrap this way. Leave 2 threads. Sealant tape Handling Caution (1) Do not apply force when transferring, mounting and dropping the regulator with a pressure gauge.
Avoid using a switch in a magnetic environment. It may cause a malfunction. 2. Use a screwdriver of a size suitable for the groove of the adjustment screw. 2. Do not use in such an environment, where water or oil is splashed.
Hysteresis free adjustments are made through a non-rising stem. Units may be base mounted, or panel mounted.
Hysteresis free adjustments are made through a non-rising stem. Units may be base mounted, or panel mounted.
Hysteresis free adjustments are made through a non-rising stem. Units may be base mounted, or panel mounted.
Hysteresis free adjustments are made through a non-rising stem. Units may be base mounted, or panel mounted.
Hysteresis free adjustments are made through a non-rising stem. Units may be base mounted, or panel mounted.
Hysteresis free adjustments are made through a non-rising stem. Units may be base mounted, or panel mounted.
Hysteresis free adjustments are made through a non-rising stem. Units may be base mounted, or panel mounted.