25 0 50 100 150 200 250 0 0 50 50 100 100 0.5 s 0.5 s 150 150 1 s 1 s 200 200 2 s 250 250 2 s 5 s 5 s 300 300 421 IZS40/41/42 Series Note) Static neutralization features are based on the data using the charged plate (size: 150 mm x 150 mm, capacitance: 20 pF) as defined in the U.S.
Note) Old VXZ bracket mounting hole center position 27 Series VXZ For Heated Water, High Temperature Oil Dimensions/Body Material: C37, Stainless Steel Grommet Conduit terminal 34 D S2 Q2 F F Q 300 D (42) 40 32 25 h a With full-wave rectifier e T R E C R d j g J C G1/2 f J OUT IN OUT IN E 2 x M Depth 5 2 x M Depth 5 G A H H G A B B1 b B B1 2 x P Port size i 2 x P Port size DIN terminal Conduit
(OUT1: Green, OUT2: Red) IP40 Operating: 0 to 50C, Stored: 10 to 60C (No freezing or condensation) Operating/Stored: 35 to 85% RH (No condensation) 1000 VAC for 1 minute between live parts and case 50 M or more between live parts and case (at 500 VDC Mega) 10 to 150 Hz at whichever is smaller of 1.5 mm amplitude or 20 m/s2 acceleration, in X, Y, Z directions, for 2 hours each 100 m/s2, in
RSH20, 32 Graph q Graph w Bore size 50, 63, 80/ = 0 Bore size 50, 63, 80/ = 0.1 1.0 RSH20 RSH32 0.9 Operating pressure ZP [MPa] 0.8 1300 1300 80 0.7 1200 1200 RSQ 0.6 1100 1100 0.5 RSG 1000 1000 0.4 900 900 0.3 RS 63 80 Load mass m [kg] Load mass m [kg] 0.2 800 800 50 0.1 MI 700 700 500 0 100 200 300 400 600 600 63 Lateral load F [N] 500 500 50 400 400 RS1H50, 63, 80 300 300 1.0 RS1H80 RS1H50
Do not drop, bump or apply excessive impacts (300 m/s2 or more for reed switches and 1000 m/s2 or more for solid state switches) while handling. Although the body of the auto switch may not be damaged, the inside of the auto switch could be damaged and cause a malfunction. 2. Mount auto switches using the proper tightening torque.
Do not drop, bump or apply excessive impacts (300 m/s2 or more for reed auto switches and 1000 m/s2 or more for solid state auto switches) while handling. Although the body of the auto switch may not be damaged, the inside of the auto switch could be damaged and cause malfunction. 2. Observe the proper tightening torque for mounting an auto switch.
Indicator light Lead wire Flexible fluorine resin heavy-duty cable, 6, 0.5mm2, 2 cores, 300 mm Impact resistance Switch part : 1000 m/s2, Connector part : 300 m/s2 Insulation resistance 50 M or more at 500 VDC (between lead wire and case) Withstand voltage 1000 VAC for 1 minute (between lead wire and case) Ambient temperature 10 to 60C Enclosure IEC529 standard IP67, JIS 0920 Watertight
Operating: 0 to 50C, Stored: 10 to 60C (with no freezing and condensation) Resistance Operating or Stored: 35 to 85%RH (with no condensation) 10 to 500 Hz with a 1.5 mm amplitude or 98 m/s2 acceleration, in each X, Y, Z direction for 2 hrs., whichever is smaller.
ZP3EA-S2 [Weight: 7.6 g] 24 47 15 29 4 20 36 Applicable pad part no. ZP3E-63UM ZP3E-80UM ZP3E-100UM ZP3E-125UM ZP3E-63BM ZP3E-80BM ZP3E-100BM ZP3E-125BM Applicable pad part no.
Grommet: G Conduit: C (Q) Approx. 300 Approx. 280 Approx. 300 D D F Q F Q Width across flats H Class H coil Broken line section C C R G1/2 R E E A H A B B 2 x P Port size 2 x P Port size 2 x M, thread depth N 2 x M, thread depth N L L K K DIN terminal: D Conduit terminal: T Cable 6 to 12 F S Q 27.5 34 F (Q) 25 R C U C (44) R E R G1/2 E G1/2 A H D (S) B B A H D 2 x P Port size 2 x P Port size
(1) 0+55() 0+40() -20+65() -15+70() 90%RH() 80%RH() 90%RH() () 1000m LECS-S5 LECS-S7 LECS-S8 () 5.9m/s2 XY49m/s2 .
Max. manufacturable stroke 25, 32, 40, 50 300 Strokes other than the above are produced upon receipt of order.
Mount the switch in a locations where there is no vibration greater than 98 m/s2 or impact greater than 490 m/s2. 3. Do not use in an area where surges are generated.
This reduces noise considerably compared with A much lower air consumption is required than the current model. the current model. 1: Conditions: Unseated for 5 seconds and seated for 20 seconds (For G type) Comparison of detection circuit ISA3 New New Current model (ISA2) A B EXH port EXH port P1 Sensor Sensor SUP port S1 S3 SUP port S2 Sensor S1 S4 S2 Detection port P2 Detection port C D
Movement Speed Position Acceleration Deceleration Force Value Area 1 Area 2 In pos force speed force mode mm/s (mm) mm/s2 mm/s2 (mm) (mm) (mm) mm/s 0 1 Absolute 100 100.00 1000 1000 50 40 10 100 0 0 5 2 Absolute 50 50.00 1000 1000 0 0 0 100 0 0 0, 1 (E.g.) Flow chart Controller (1) Select/input Step No.1.
Weight Series Stroke[mm] 50 100 150 200 250 300 350 400 450 500 600 700 800 LEKFS25 Product weight[kg] 1.7 1.8 2.0 2.1 2.3 2.4 2.5 2.6 2.8 2.9 3.2 3.5 3.8 0.26 Additional weight with lock[kg] LEKFS32 Series Stroke[mm] 50 100 150 200 250 300 350 400 450 500 600 700 800 900 1000 Product weight[kg] 3.6 3.8 4.0 4.2 4.5 4.7 4.9 5.1 5.3 5.5 5.9 6.3 6.7 7.1 7.5 0.53 Additional weight with lock[kg
In the case of cylinders with built-in magnets, unassembled auto switch mounting brackets are packed together when shipped. 11 Series CQM Auto Switch Specifications Auto Switch Common Specifications Reed switch Type Leakage current Solid state switch 3-wire: 100 A or less, 2-wire: 0.8 mA or less None 1 ms or less Note 2) Operating time 1.2 ms Impact resistance 300 m/s2 1000 m/s2 Note1) Connector
Do not drop, bump, or apply excessive impact (100 m/s2) while handling. Although the body of the controller case may not be damaged, the inside of the controller could be damaged and cause malfunction. 2. The tensile strength of the power supply/output connection cable is 50 N; that of the pressure sensor lead wire with connector is 25 N.
Grommet L plug connector MN: Without lead wire WO: Without connector cable G: Lead wire length 300 mm L: With lead wire (Length 300 mm) M: With lead wire (Length 300 mm) D, Y: With connector Coil type + + Standard Nil T With power saving circuit (24, 12 VDC only) + + + + + + Power saving circuit is not available for D, Y, DO, YO or W types.