VDW Series, Compact Direct Operated 2/3 Port Solenoid Valve for Water and Air Note 4) (ft/s2) 30/150 (9/150ft/s2) Rated voltage 24VDC, 12VDC, 100VAC, 110VAC, 200VAC, 220VAC (50/60Hz) Allowable voltage fluctuation % 10% of rated voltage Coil insulation type Class B Enclosure Note 5) Dust proof (equivalent to IP40) Power consumption W Note 3) 2.5 (VDW10), 3 (VDW20/30) Note 1) Consult P/A when used under conditions which may cause condensation on the exterior of the
Do not drop, bump or apply excessive impacts (300 m/s2 or more for reed auto switches and 1000 m/s2 or more for solid state auto switches) while handling. Although the body of the auto switch may not be damaged, the inside of the auto switch could be damaged and cause malfunction. 2. Observe the proper tightening torque for mounting an auto switch.
Mounting orientation is Upper direction Model Port size Rc(PT) 63 63 80 85 90 100 B C A INA-11-402 INA-11-403 INA-11-404 INA-11-405 INA-11-406 INA-11-407 1/4 141 164.5 170 180 230 251 15 15 15 20 22 22 3/8 1/4, 1/2 3/8, 3/4 3/4, Bracket dimensions Model Port size B C D E A 1 F 345 419.2 K 57 49.6 J 14 14 H 95 120 G 32.5 0 1 1 1 1 2 4, 1 2, 1 175 250 175 250 87.5 125 460 613 135 209 4, 3 ALD600
Prefix it to the part nos. of the solenoid valve, etc. 5-4-3 Series SYJA300 Specifications Compact and lightweight Fluid Operating pressure range (MPa) Pilot pressure range MPa Note 1) Air 0.15 to 0.7 Operating pressure range to 0.7 Ambient and fluid temperature (C) Lubrication Mounting orientation Impact/Vibration resistance (m/s2) Note 2) 10 to 50 (No freezing. Refer to page 5-11-4.)
Manual override (2) Non-locking push type, Locking slotted type, Locking lever type Pilot exhaust method Lubrication Mounting orientation Impact/Vibration resistance (m/s2 )(3) Individual pilot exhaust type, Common exhaust (pilot and main valve) type Not required Unrestricted 300/50 Dustproof Enclosure Note 1) Based on dynamic performance test, JIS B 8375-1981.
Control equipment connected to the barrier must not use or generate more than 250 V. 2. Installation should be in accordance with Canadian Electrical Code or ANSI/ISA RP12.6 Installation of Intrinsically Safe Systems for Hazardous (Classified) Locations and the National Electrical Code or ANSI/NFPA 70. 3.
Do not drop, bump, or apply excessive impacts (300m/s2 or more for reed switches and 1000m/s2 or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 5. Do not allow short circuiting of loads.
Vibration resistance (Excluding valve manifold) Conforms to EN61131-2 Impact resistance 147 m/s2, 11 ms (Excluding valve manifold) Standard CE marked Weight 300 g Communication standard ISO/IEC14430B (Type-B) NFC communication specifications Frequency 13.56 MHz Communication speed 20 to 100 kHz (I2C) Communication distance Up to 1 cm 1: The configuration file can be downloaded from the
+50oC Ambient temperature (storage temperature) -20 to +60oC Ambient humidity 35 to 85% RH (no condensation) Withstand voltage 500 VAC-1 minute between external terminals and metallic parts Insulation resistance 10 M or more (500 VDC between external terminals and metallic parts) General specifications Conforms to EN61131-2 5 f < 8.4 Hz 3.5 mm Vibration resistance 8.4 f < 150 Hz 9.8 m/s2
Note 4) When the stroke is 25 mm, the maximum speed will be 250 mm/sec. Note 5) Set to the pushing speed when pushing operation. Note 6) The speed and force may change depending on the cable length, load and mounting conditions. Furthermore, if the cable length exceeds 5 m, then it will decrease by up to 10% for each 5 m.
The unit conversion between SI and conventional units are as follows: Oscillation acceleration 100m/s2 = 10.1972G Pressure 1MPa = 10.1972kgf/cm2 Cylinder thrust/load 100N = 10.1972kgf Standard air: Symbol (ANR) Torque 1Nm = 10.1972kgfcm Temperature 20C {293K}, Air with Moment of inertia 1kgm2 = 10.1972kgcm/s2 an absolute pressure of 760 mmHg Kinetic energy 1J = 10.1972kgcm {101.3kPa}, and
This reduces noise considerably compared with A much lower air consumption is required than the current model. the current model. 1: Conditions: Unseated for 5 seconds and seated for 20 seconds (For G type) Comparison of detection circuit ISA3 New New Current model (ISA2) A B EXH port EXH port P1 Sensor Sensor SUP port S1 S3 SUP port S2 Sensor S1 S4 S2 Detection port P2 Detection port C D
Bore size CS1, CS2 series Pressure 0.5 MPa Load ratio 50% Stroke 1000 mm MB, CA2 series Pressure 0.5 MPa Load ratio 50% Stroke 500 mm Average speed [mm/s] Series 40 50 63 80 100 125 140 160 180 200 250 1100 1000 900 800 700 600 500 400 300 200 100 0 Vertically upward Horizontal VQ4100--03 VQ4101--03 1100 1000 900 800 700 600 500 400 300 200 100 0 VQ5100--04 VQ5101--04 Values at extension
: Individual take out of A and B sides K plug connector type: Common take out of A and B sides DIN terminal type: individual take out of A and B sides A little power consumption: 1.8 WDC For serial transmission EVS Fluid Maximum operating pressure Minimum operating pressure Proof pressure Ambient and fluid temperature Lubrication Pilot valve manual override Shock/Vibration resistance (m/s2
Do not drop, bump, or apply excessive impacts (300m/s2 or more for reed switches and 1000m/s2 or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 5. Do not allow short circuiting of loads.
Note) If the set pressure is 250 kPa and the output pressure on the pressure sensor is 245 kPa, the deviation is 250 245 = 5 kPa. In order to correct the deviation, the controller increases the output signal until the pressure on the pressure sensor converges at 250 kPa. Step 1 Step 2 Step 3 Step 4 . . . . . . . . . . . . .
When you carry out adhesion mounting of the driver, make circumference temperature into 0 to 45 (32 to 113 ), or use it at 75% or smaller effective load ratio. 1000 1000 During operation During operation 100 100 Operation time[s] Operation time[s] During servo lock During servo lock 10 10 1 1 0.1 0.1 0 50 150 200 250 300 100 0 50 150 200 250 300 100 (Note) Load ratio [%] (Note) Load ratio
When you carry out adhesion mounting of the driver, make circumference temperature into 0 to 45 , or use it at 75% or smaller effective load ratio. 1000 1000 During operation During operation 100 100 Operation time[s] Operation time[s] During servo lock During servo lock 10 10 1 1 0.1 0.1 0 50 150 200 250 300 100 0 50 150 200 250 300 100 (Note) Load ratio [%] (Note) Load ratio [%] LECSS-S5
Note) If the set pressure is 250 kPa and the output pressure on the pressure sensor is 245 kPa, the deviation is 250 245 = 5 kPa. In order to correct the deviation, the controller increases the output signal until the pressure on the pressure sensor converges at 250 kPa. Step 1 Step 2 Step 3 Step 4 . . . . . . . . . . . . .
Impact acceleration [m/s2] 5 0 50 100 150 200 250 300 Speed [mm/s] Relationship between speed and impact acceleration 8-18-2 in vacuum environments (1.3 x 104 Pa) Carefully designed for low particulate generation, low leakage, and low outgassing.