Rubber grommet Signal cable entry L N PE Strain relief Power supply cable entry IDFC60/70/80/90 Series 2.1Name and Function of Parts 2-1 IDX-OM-U010 Chapter 2 Name and Function of Parts Left ventilation grille (air intake opening) (Dustproof filter) Air intake for cooling.
Proper tightening torque M1.4 : 0.06Nm M2 : 0.16Nm M3 : 0.8Nm 1. Leakage between valve and base. (Base mounted type) Leakage between body and PE plate.
to MIL-C-83503) 3.1 8 36.3 5.5 5.3 LOCK FREE Triangle mark 35 18 28.8 A B A B 47.6 A A A 58.2 DIN rail 6 Triangle mark position 7.9 Manual override 22 36.1 In case of locking type, turn after pushing in. ( ) 3.5 (With switch) Power supply terminals (M3 terminal screws) 4 (A): Orange 2 (B): Green L2 (Rail mounting hole pitch 12.5) 5 DIN rail holding screw L1 (Station n).
Function 3 () Sensor power supply 3 SW 2 3 4 1 SV24V For solenoid valve +24V 4 Sensor input signal SIGNAL 4 2 SV0V For solenoid valve 0V 5 5 Protective sensor ground PE 3 Protective ground PE 1 5 The second pin of the connector with input no. 0, 2, 4, 6 (the connector at the right side of the input block) is connected internally to the fourth pin (sensor input no.) of the connector with
For grounding actuator, connect the copper wire of the actuator to the driver,s protective earth (PE) terminal and connect the copper wire of the driver to the earth via the control panel,s protective earth (PE) terminal. Do not connect them directly to the control panel,s protective earth (PE) terminal.
(PE) port leakage from the piping between the valve and the cylinder. If the solenoid valve and the manifolds pilot EXH (PE) port is restricted extremely or blocked, abnormal operation of the solenoid valve may occur. 5.
M3 x 0.5 18 0.9 M3 x 0.5 39 (Without subplate 18) Base mounted (with sub-plate) 0.089 M5 x 0.8 0.36 0.31 0.089 0.36 0.31 N.O.
This is a legacy product, and replaced bySY124A-5LZ, VALVE,PILOT(NORM OPEN), VALVE, VJ100 SOL VALVE 3-PORT, 2B, VJ100 NO SIZE RATING, 0.0286 lb
*ZSE10ZL3,ZL6 5.2 1) 2) 3), 4) 5)1015 10 1% 6), 7)LCD 8)FG 14 No.ZL3-OM00801-A . 6.1 ON 6.2 1) 2) 3), 4)12 5) 15 No.ZL3-OM00801-A 7 , 7.1 ZL3 ZL3 ZL6 ZL6 14 1 7 15 PBT 2 POM 16 POM 2 3 PBT 17 PBT 4 POM 18 5 FKM 6 PBT 19 7 PBT 3 6 8 1 PBT 20 , 9 1 4 1 10 2 21 11 2 PBT 5 22 12 POM 8 13 3 O HNBR/NBR 16 No.ZL3-OM00801-A 7.2 1 (/) ZL3/ZL6 ZL3-JSY3140-5LZ
Round head screw (M3 x 8) 4 pcs. Enclosed parts Round head screw (M4 x 6) 2 pcs. Round head screw (M3 x 8) 4 pcs. 13 Accessories Series EX600 Reinforcing brace This bracket is used on the bottom of the unit at the intermediate position for connecting 6 units or more. For direct mounting EX600-ZMB1 For DIN rail mounting EX600-ZMB2 Enclosed parts Round head screw (M4 x 5) 2 pcs.
Circulating fluid : Tap water Density : 1 x 103 kg/m3 Specific heat C : 4.2 x 103 J/(kgK) Refer to the information shown below for the typical physical property values by circulating fluid. Water bath Q = T x V x x C h x 60 x 1000 10 x 2 x 1 x 103 x 4.2 x 103 20C V = 15 x 60 x 1000 After 15 min, = 93.3 W cool 30C down to 20C.
Required ventilation rate [m3/min] Heat radiation amount [kW] Differential temp. of 6C between inside and outside of installation area HRS090-A-20/40 17 290 145 Differential temp. of 3C between inside and outside of installation area Model 89 A HRS090 Series Specific Product Precautions 3 Be sure to read this before handling the products.
/h) (282 m3/h) (420 m3/h) (570 m3/h) dew point Standard Outlet air condition 45oF 155SCFM 215SCFM 314SCFM 406SCFM Air flow capacity pressure (7.2oC) (264 m3/h) (366 m3/h) (534 m3/h) (690 m3/h) (ANR) dew point (Note2) Outlet air 50oF 177SCFM 251SCFM 353SCFM 459SCFM pressure (10oC) (300 m3/h) (426 m3/h) (600 m3/h) (780 m3/h) dew point Rated Inlet air pressure 100 psi (0.7MPa) condition Inlet
a ZQ sl or an l f ea te d ZF id wo pe rk ZP ty su nt ZCU oi rf ac l j AMJ al e s B Misc.
SY100-68-A-20 W2WA2500mm W3WA31000mm <2> 300mm W4WA42000mm SYJ312-5LPZ-M3 W7WA75000mm Assy Ass'y SYJ312-5W1ZE-M3 13 No.SYJ300-OMU0003 SYJ Series M8 10COM2 B 12 DCU+COM-COM 1 3 4 L 300mm V100-49-1-1 500mm V100-49-1-2 A B A B A B A B 1000mm V100-49-1-3 A B COM (+)(-) COM (+)(-) 2000mm V100-49-1-4 5000mm V100-49-1-7 (+)(-) (+)(-) (+)(-) (+)(-) (+)(-) (+)(-) (+)(-) (+)(-) (+)(-) (+)(-)
SOL. VALVE, BODY PORTED, 4/5 PORT SOLENOID VALVE, O84, 28 lb
Example of the conventional measurement units (Reference) Unknown 6.0C 20C 26C 1.2 m3/h Fluorinated fluid Density : 1.80 x 103 kg/m3 : Unknown : 6.0C (6.0 K) : 20C (293.15 K) : 26C (299.15 K) : 20 l/min : Fluorinated fluid Density : 1.80 x 103 kg/m3 Heat generation amount Q Circulating fluid temperature difference T (= T2 T1) Circulating fluid outlet temperature T1 Circulating fluid return
50/60 Hz 200 V 50/60 Hz 220 V 50/60 Hz M plug connector Sonic conductance C [dm3/(sbar)] L plug connector 24 V Series M8 Connector Pressure center 12 V DIN terminal Closed center Exhaust center 6 V Grommet { } 4/25/3 (A/BEA/EB) Double 5 V Single 3 V P.1 SY3 20 0.65 Body ported Base mounted Body ported Base mounted SY5 20 2.4 SY7 20 3.3 SY9 20 8.6 P.19 SY3 40 1.1 SY5 40 2.8 SY7 40 A B 4.5 PE
View A L1 L2 L3 PE Inlet of the power supply cable Mount for cable tie Note: Prepare a cable tie. Fasten the power cable to the mount on the base with the cable tie.
Ordinarily, air is discharged from the bleed hole (PE). The consumption of air through this discharge is normal, owing to the construction of the precision pressure reducing valve. 3.