HRX-OM-W058 Depending on the external switch output type, wire the switch to the communication connector for contact input / output (which is included as an accessory) as shown below. Mount the ferrite core (3 turns), which is included as an accessory. This is an example of wiringRefer to the Communications Operation Manual for more details.
the connections from Rc to NPT is enclosed as an accessory.
) Input 0 Input 0 a a b Input signal range a 0 to 10 V Input signal range a b 1 to 5 V Input signal range a b 10 to 10 V 10 V 1 V 5 V 10 V 10 V 0 to 5 V 5 V 4 to 20 mA 4 mA 20 mA 5 to 5 V 5 V 5 V 0 to 20 mA 20 mA 20 to 20 mA 20 mA 20 mA Regarding AD value In the above graph, 3 AD values are explained as below. 31208 : AD value [Decimal value] (F9E8): Signed Binary type [Hexadecimal value]
(The motor rotates in the reverse direction if the table hits an obstacle such as the end stop damper.) Take the motor phase detection step into consideration for the installation and operation of this electric actuator. Caution 1. Keep the driver and product combined as delivered for use. The product parameters are set before shipment.
As th r6st oosition is rc', all end-of-stroke valves operated in the rest position have an index zero. Those opratd in the opposlte end (\^,ork position") have an index "1". Fig.
As th r6st oosition is rc', all end-of-stroke valves operated in the rest position have an index zero. Those opratd in the opposlte end (\^,ork position") have an index "1". Fig.
Input block specifications Valve stations PNP sensor input (Positive common) or without input block Nil Symbol 02 Stations 2 stations Note N NPN sensor input (Negative common) Double wiring Note 1) 16 02 16 stations 2 stations Note 2) Specified layout (Up to 32 solenoids possible) 20 20 stations When the SI unit is for AS-i, the maximum numbers of solenoids are as follows.
The grounding point should be as near as possible to the controller, to keep the grounding cable as short as possible.
(REH/Linear guide type) Series REAL Size: 10, 15, 20, 25, 32, 40 To ensure a permanent path When smoother operation is required, even with an offset load Stable operation is possible, even with an offset load, by using ball bushings. Series REAH Size: 10, 15, 20, 25, 32 The use of a linear guide facilitates a large load, large moment.
For pipe thread type N, an NPT thread conversion fitting set is included. 19 Not included for Option Z (Removed parts) 20 Not included for Options Z and Z1 (Removed parts) 15 Thermo-chiller/Rack Mount Type HRR Series Specifications: 200 to 230 VAC Water-cooled Refrigeration Model HRR012-W-20 HRR018-W-20 HRR024-W-20 HRR030-W-20 Cooling method Water-cooled refrigeration Refrigerant R410A
to 100 only -XC59 Fluoro rubber for seal/Built-in hard plastic magnet, 20 to 100 only -X202 Same overall length dimension as Series CQ1, Except 16, 25 -X203 Same L dimension from rod cover as Series CQ1, 20, 32 only -X293 Same overall length as Series CQ1W, Except 16, 25 -X144 Change of port location, 12 to 25 only -X271 Fluoro rubber for seals -X525 Long stroke of adjustable extension stroke
Cylinder stroke (mm) 20 32 40 50 10, 15, 20 10, 15, 20 20, 25, 30 20, 25, 30 Built-in Magnet Cylinder Model If a built-in magnet cylinder without an auto switch is required, there is no need to enter the symbol for the auto switch. (Example) 90-RSDQB32-15D *Specifications and dimensions for the 90-series are the same as standard products.
Enable Generates an error. 1 Unit Disable Does not generate an error. -10..10 V -5..5 V -20..20 mA 0..10 V Selects the analogue input range. -10..10 V Channel 2 Analogue input range Sets the analogue input device range. 0..5 V 1..5 V 0..20 mA 4..20 mA Offset binary Offset binary.
Equipped with an auto switch (Mountable on both sides) Magnet included as standard. Reed auto switch: D-A7/A8 Solid state auto switch: D-F7/J7 ( ) Series MRQ An air cushion is also available.
The purpose of an air cushion is not to reduce the speed of a piston as it nears the stroke end.
10-20-59 With built-in OFF-delay timer (200 ms) CE1 D-G5NTL D-F7NTL D-F5NTL D-M5NTL/M5PTL 10-20-60 Grommet Band Solid state switch With timer 10-20-61 Grommet Rail CE2 10-20-62 Grommet Tie-rod 10-20-63 Grommet Direct ML2B Possible to use in an environment where disturbance magnetic fields are generated.
For an exterior dimension diagram to identify the mounting support types, refer to p.3.1-21 to 3.1-24 as the dimensions are identical to those of standard.
Model HTB 1 8 Rc CY1S20 CY1S25 CY1L25 CY1S32 CY1L32 CY1S40 CY1L40 20 20 7.5 20 20 7.5 1 8 Rc 20 23 8.2 24 24 7.5 1 8 Rc 26.5 26.5 8.2 25 25 8 1 4 Rc 30.5 30.5 11 Dimensions except mentioned above are the same as standard type of Series CY1B. Refer to page 8-15-24.
If the input or output size is an odd number, add 1 byte, to make it an even number of bytes. The I/O map is shown with the following unit configuration as an example.
.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com 4 Electric Actuator with Integrated Guide Series LTF Lead screw lead mm Mounting orientation Motor type Series Page Model Guide type Ground ball screw Rolled ball screw 6 10 20 10 20 10 20 10 20 6 10 20 10 20 10 20 10 20 LTF6 LTF8 LTF6 LTF8 LTF6 LTF8