CJ2 B B A B A A B B A 1 (0) 1 (7.5) 2 (0.5) 2 (8.5) 6 CJ1 10 16 1.5 2 1.5 2 2.5 3 2.5 3 3 3.5 3 3.5 3.5 4 3.5 4 0.5 1 0.5 1 CJP Figures in parentheses for bore 6 are in the case of double rod type, (Series CJ2W).
Use caution to the popping of a snap ring. When replacing rod seals and removing and mounting a snap ring, use a proper tool (snap ring plier: tool for installing a type C snap ring). Even if a proper tool is used, it is likely to inflict damage to a human body or peripheral equipment, as a snap ring may be flown out of the tip of a plier.
A11 Symbol: A12 Symbol: A13 Symbol: A14 DA DA C0.5 R ball AL MM 30 30 DA C R ball TP R ball A A H C H T W1 H H H Symbol:A15 Symbol: A16 Symbol: A17 Symbol: A18 Symbol: A19 DA AL MM 30 DA MM 30 MM 30 MM 30 C 30 A H H A H A A C H A H Symbol: A20 Symbol: A21 Symbol: A22 Symbol: A23 Symbol: A24 30 30 DA L RD MM 30 DA MM 30 MM MM DB DB T T C B A H AL H A L K H A A W H H Symbol: A25 Symbol:
+ A = 100 y, z + A 100 10 y, z + A = 200 y, z + A = 200 y, z + A = 300 y, z + A = 300 1 1 0 200 400 600 800 1000 1200 0 100 200 300 400 500 600 700 800 Stroke [mm] Stroke [mm] [Graph 6] Allowable load mass by stroke 32 [Graph 5] Allowable load mass by stroke 25 100 100 y, z + A = 0 y, z + A = 0 y, z + A = 50 y, z + A = 50 10 Load mass [kg] Load mass [kg] 10 y, z + A = 100 y, z + A = 100
Bore size (mm) D-A73/A80 D-F7NT Electrical entry (Fetching direction) Type Model Features D-F7NT Solid state auto switch Grommet (In-line) With timer A B A B A B With pre-wired connector is available for D-F7NT type, too.
Extend the dimensions of A, H. when using a single/double knuckle joint together with a rod end nut. (To extend dimensions A/H, refer to the table below, and specify the product as Made-to-order -XAO.)
on handling Note 1) When using as a stopper, select a model with 50 stroke or less.
When tightening the auto switch mounting screw, use a watchmakers screw driver with a handle diameter of about 5 to 6mm. Furthermore, use a tightening torque of 0.05 to 0.1 Nm. As a rule, it should be turned about 90 from the point at which tightening can be felt. Use a tightening torque of 1 to 1.2 Nm for the hexagon socket head set screws (M4 x 0.7). 1.
Use a dedicated hose nipple. On the panel mounting style, use the CJ5H-4 or CJ-5H-6, a dedicated hose nipple (with a fixed orifice) that is provided. If a different fitting must be used due to unavoidable circumstances, make sure to install a speed controller and use it by adjusting it to 500 mm/s or less.
Use a dedicated hose nipple. On the panel mounting style, use the CJ5H-4 or CJ-5H-6, a dedicated hose nipple (with a fixed orifice) that is provided. If a different fitting must be used due to unavoidable circumstances, make sure to install a speed controller and use it by adjusting it to 500 mm/s or less.
Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.
When used without a guide for a light load. (Application Example 1) When space is very limited. Series CY1S Size: 6, 10, 15, 20, 25, 32, 40 Smooth operation is possible through the use of a special slide bearing. To ensure a permanent path. When used for general transporting. A load can be carried directly by the integrated guide type.
Operating principle A + A' A' A Piston seal A' A' R H R H When the piston is retracting, air is exhausted through both A and A' until piston seal H passes air passage A. After piston seal H has passed air passage A, air is exhausted only through A'. The section marked with slanted lines becomes a cushion chamber, and an air cushion effect is achieved.
Refer to the Specific Product Precautions for the replacement period. 1517 A
A double knuckle joint pin and retaining rings are shipped together.
(For band mounting, only the auto switch mounting brackets are assembled before shipment.) * When mounting a band on bore size 8, 10, or 12, the D-A9l(V) cannot be mounted. * When mounting a rail on bore size 8, 10, or 12, the D-A9l(V) and A79W cannot be mounted. * When mounting a rail on bore size 20 or 25, the D-M9l(V), M9lW(V), and M9lA(V) cannot be mounted. 2 C85 Series Specications Bore
CM2 A B Z 40 150 CDM2 With auto switch M9BW 150 A B 40 Z Port thread type Number of auto switches Rod end bracket With auto switch (Built-in magnet) Nil Rc TN NPT TF G Nil None V Single knuckle joint W Double knuckle joint Mounting Nil 2 pcs. S 1 pc. n n pcs.
CM2 L A 40 150 M9BW With auto switch CDM2 L A 150 40 Number of auto switches Rod boot With auto switch (Built-in magnet) Type None Nil J K Nil H 2 pcs. Nil S n Pneumatic Nylon tarpaulin Air-hydro 1 pc. Port thread type Heat resistant tarpaulin n pcs.