CE2 Cover Rod cover Unit holding tie-rod A (2 depth 1 mm hole is on the side of tie-rod for attaching unit A.)
Internal data error H Anti-chattering function (F3) A large bore cylinder or ejector consumes a large volume of air in operation and may experience a temporary drop in the supply pressure. This function prevents detection of such temporary drops in the supply pressure as an error. K Secret code setting (F10) OUT Input an arbitrary three-digit value.
A B PFMV5 Series 1.00 5.00 Set A and B to the values shown in the table on the left.
The double clevis style is provided with a clevis pin and a snap ring.
' view RE A B Breathing hole REC A-A' view CX CY MQQ M RHC Manual button MK(2) RS Q G RS H A RZQ MI W S Non-lube type Long stroke type CEP1 CE1 Component Parts CE2 Note Material Material No.
pin should be used together with a plain washer.
Apply a tightening torque of 0.98 Nm or less. Rear piping ... Bracket A (Model: ZS-24-A) Bracket D (Model: ZS-24-D) Bottom piping ... Bracket B (Model: ZS-35-A) Hysteresis H_1 WARNING indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury.
D-Y7WV D-Y7BAL D-A3 D-A44 D-G39 D-K39 D-A5 D-A6 D-A59W D-F5NTL D-F5LF D-P5DWL Bore size (mm) A A A A B A A A A B B B B B B B 32 12 11 7 4.5 0 0.5 3.5 4 0.5 9.5 8.5 4.5 2 1 1.5 0 40 12 11 7 4.5 0 0.5 3.5 4 0.5 9.5 8.5 4.5 2 1 1.5 0 50 12.5 11.5 7.5 5 0 1 4 4.5 1 10 9 5 2.5 1.5 2 0 63 12.5 11.5 7.5 5 0 1 4 4.5 1 10 9 5 2.5 1.5 2 0 80 15.5 14.5 10.5 8 2.5 4 7 7.5 4 14 13 9 6.5 5.5 6 2.5 100
Lock ring Warning: Danger: WARNING indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Used to mount the product on a DIN rail or directly to a panel. Mounting hole [F10] [F11] [F12] [F13] [F98] [F99] The body of the product.
Warning: WARNING indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury.
The product is a approved product only if it has a mark on the body. [A ir ] dry air, N2 [FLU] Operating fluid [F 3] Check that the above preparation has been performed correctly, then part A shown should be pressed in by hand to make temporary connection. Part A should then be pressed in using a suitable tool, such as pliers.
Check that the above-mentioned preparation work has been performed correctly, and part A shown in the figure is pushed by hand and makes temporary connection. Part A centre is pushed straight in using a suitable tool, such as pliers. Re-use cannot be performed once it connects the connector for sensor connection completely.
When a switch-mode power supply is connected to the product, switching noise will be superimposed and the product specification can no longer be met. This can be prevented by inserting a noise filter, such as a line noise filter and ferrite core, between the switch-mode power supply and the product or by using a series power supply instead of a switch-mode power supply.
When a switch only is shipped, "BBA1" screws are attached. Flange MB-F03 MB-F04 MB-F05 MB-F06 MB-F08 MB-F10 Single clevis MB-C03 MB-C04 MB-C05 MB-C06 MB-C08 MB-C10 Double clevis MB-D03 MB-D04 MB-D05 MB-D06 MB-D08 MB-D10 Note 1) Two foot brackets required for one cylinder. * Accessories for each mounting bracket are as follows.
When a switch only is shipped, "BBA1" screws are attached. Flange MB-F03 MB-F04 MB-F05 MB-F06 MB-F08 MB-F10 Single clevis MB-C03 MB-C04 MB-C05 MB-C06 MB-C08 MB-C10 Double clevis MB-D03 MB-D04 MB-D05 MB-D06 MB-D08 MB-D10 Note 1) Two foot brackets required for one cylinder. * Accessories for each mounting bracket are as follows.
Solid state auto switches are also available with a pre-wired connector. Refer to pages 1328 and 1329 for details. D-A9/M9/M9W/M9AL auto switches are shipped together (not assembled).
This is a legacy product, and replaced byAL60-F10-8-A AL MASS PRO. LUBRICATOR. AIRLINE EQUIPMENT. AL MASS PRO 1 MODULAR (PT). 1.56645 lb. HA.