ＳＭＯＯＴＨ ＣＹＬＩＮＤＥＲ Do not use until you verify that the equipment can operate properly. After mounting, repair or modification, etc., connect the air supply and electric power, and then confirm proper mounting by means of appropriate function and leak inspections. Do not let chips or extraneous material enter inside the cylinder from the inlet.
When performing neutralization, do not input the ionizer stop signal.
Piston rod Do not turn the screws at the bottom. Do not damage the sliding surface of the piston rod of the shock absorber. Otherwise, impaired durability and return failure can result. Damage is not allowed. Shock absorber is a consumable. Replace the shock absorber when the energy absorption performance is reduced.
Do not use in the environment, where the product could be exposed directly to the foreign matters such as powder dust, blown dust, cutting chip, spatter etc. This could result in looseness and increased operating resistance, and air leakage, etc. Please consult with SMC regarding use in this kind of environment. 3. Do not use in direct sunlight. 4.
Do not rotate the screw set on bottom of shock absorber. This is not an adjusting screw. Turning it could cause oil leakage. 2. Do not scratch the exposed portion of the piston rod. Durability could be degraded and lead to return defect.
Comfirm that the auto drain operates in the case of type with auto drain. 2.Confirm that air leakage do not occur.
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. 3. Do not service or attempt to remove product and machinery/equipment until safety is confirmed. 3.
Do not use the product in an environment that is exposed to temperature cycle. Do not expose the product to direct sunlight. Keep the specified ambient temperature range. Do not expose the product to heat radiation from a heat source located nearby. Set the switches by using a sharp-pointed screwdriver etc.
Do not use the product in an environment that is exposed to temperature cycle. Do not expose the product to direct sunlight. Keep the specified ambient temperature range. Do not expose the product to heat radiation from a heat source located nearby. Set the switches by using a sharp-pointed screwdriver etc.
Do not use the product in an environment that is exposed to temperature cycle. Do not expose the product to direct sunlight. Keep the specified ambient temperature range. Do not expose the product to heat radiation from a heat source located nearby. Set the switches by using a sharp-pointed screwdriver etc.
Do not rotate the cover. If a cover is rotated when installing a cylinder or screwing a fitting into the port, it is likely to damage the junction part with cover. 2.Do not operate with the cushion needle in a fully closed condition. Using it in the fully closed state will cause the cushion seal to be damaged.
Use clean ai Do not use compressed air that contains chemicals, synthetic oils that include organic solvents, salt, corrosive gases, etc., as it can cause damage or malfunction. Do not use in an environment where flammable gas or explosive gas exists. Usage may cause a fire or explosion. The products do not have an explosion proof construction. 3.
Sensuous phenomenon nothing to do with function.
B Supply pressure and the Stopper screw (Do not move) OUT1 output are connected by rotating the Auto/Manual changeover screw towards M.
Do not place electrical wiring in hazardous places while energized. Caution ! To prevent risks while pressure is supplied, do not touch areas surrounding driving components such as actuators and valves. Be sure to mount the body cover unit when using the positioner. IP 65 cannot be guaranteed if the mounting condition of the body cover is incorrect.
Do not use in an environment where flammable gas or explosive gas exists. Usage may cause a fire or explosion. The products do not have an explosion proof construction. 3. Do not use in a place subject to heavy vibration and/or shock. 1. Drain flushing Remove drainage from the air filters regularly. 2. Lubrication Once lubrication has been started, it must be continued.
Do not use the product in an environment where corrosive gases or fluids could be splashed. Otherwise damage to the product and malfunction can result. Do not use in an area where surges are generated.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate or set with wet hands. This may lead to an electric shock. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. Do not use the components other than the specified components. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
If they do not match, stress could be applied to the rod and the cylinder tube, causing wear to the inner surface of the cylinder tube, the bushing, the rod surface, and the seals may become damaged. 3) When mounting the cylinder, do not apply a lateral load to the rod.